Drag Race Car Wiring
Ok race car wiring gurus…
A friend of mine has purchased a 3/4 chassis 85 Rx-7. It came straight from the chassis shop in South Florida and I am going to be helping him build it from the there up. One of my first tasks is to wire up the car for fuel pump, ignition, starter, gauges, ECU, etc. I ordered a Painless Fused Switch Panel from Jegs. This panel doesnt include relays but includes fuses. In my opinion it seems that everything should be run off a relay. If this is the case then why would painless sell a switch panel that has fuses but no relays. All the current will go through the switch ? does that make sense???? I called Painless wiring and they said, ‘just follow the colors on the directions’. The battery is located in the trunk area. Correct me if I am wrong here..... I need to run the thick the a$$ wire red wire that came with a battery relocation kit straight to the starter. Another wire from the alternator all the way back to the battery. Another wire to the painless switch panel straight from the battery (fused at the battery). Another thick wire (gauge?) to a separate fuse box up front that will be used for the relay powered fan, ecu, injectors, etc. I realize there is more than one way to do things but I want to do it the best way. Any input, suggestions or links that would help is appreciated. Danny |
Danny,
Check your rules on Battery kill switches, as a drag car I'm 100% sure you have to run a kill switch with a relocated battery, and that means your wiring changes. Never setup a Painless panel, but it sounds like it was designed to go through the switch.. Maybe that's why it's called Painless :) If it were me, I'd run a heavy guage wire from the battery to a fuse box in the middle of the car, and fuse in all your various power needs into that wire, rather than run all your leads back to the battery. Run the alternator wire all the way back (you'll have to run it to the kill switch) so make sure that's a heavy guage wire as well. Good luck! PaulC |
Or you connect the altenator to the same point on the starter. Surely that would do the same job, but with less wire? (as long as it's a sonolid controlled starter anyway)
|
hey i rewired my drag car you have to have the postive cable run o the switch then use a high amp relay to shut down the alt
|
yeah i think I am going to run one 2ga wire from the battery through the disco switch and up to the starter. from the starter it will go to the alternator & fuse panel. That should make for a neat job.
I will use relays on the fuel pump and anything that would exceed the switches amperage capability. Now all I have to do is figure out how the hell to crimp a 2 ga wire! Thanks guys Danny |
I used 00 ga with ends form mcmaster. the cable end i used was J. theres no criping tool needed it clamps down on the wire when u crank in on the nut. Heres the link
http://www.mcmaster.com/asp/DisplCtl...D=ToolPageFlip |
Originally posted by dcee Now all I have to do is figure out how the hell to crimp a 2 ga wire! |
Originally posted by yallgotboost I used 00 ga with ends form mcmaster. the cable end i used was J. theres no criping tool needed it clamps down on the wire when u crank in on the nut. Heres the link http://www.mcmaster.com/asp/DisplCtl...D=ToolPageFlip Sweeeet. I love Mcmaster. Thanks for the tips guys. |
Now all I have to do is figure out how the hell to crimp a 2 ga wire! |
IIRC, we took solder, used a propane torch to heat up the connector, stuck the wire down there, with solder, and let the heat of the connector melt the solder..
Then we 'crimped' it with a hammer :) PaulC |
All times are GMT -5. The time now is 11:58 PM. |
© 2024 MH Sub I, LLC dba Internet Brands