Chassis straightener FD specsheet
I'm looking at buying ChassisSim Lite.
http://www.chassissim.com/ I need the dimensions of the FD suspension geometry. I figure the best way to do it is to get a chassis machine set-up sheet for FD. I don't know what you call the sheet, the one they use to see if your crashed FD is straight before they put it back together :) That will give me the suspension point locations then i need to measure the suspension arms. Q1 has anyone already done this and can you give me the data Q2 has any one got an FD chassis machine set-up sheet for the FD chassis? I don't mind drawing it up in 3D if some one can find the sheet for me. |
You want the Collision Repair Manual:
http://www.wrex-racing.com/web/fd/info.htm |
do they have 1 of those for the FC ? I need some misc parts
|
In industry its simply called "frame specs"
Any body shop with a Mitchell Estimating system should be able to provide you with them, they may charge a fee though - that system is pricey. It'll give you a few measurements from various chassis points as well as measurements for heights of those points from a datum line. |
Originally Posted by Mahjik
(Post 8449629)
You want the Collision Repair Manual:
http://www.wrex-racing.com/web/fd/info.htm |
Originally Posted by classicauto
(Post 8450953)
In industry its simply called "frame specs"
Any body shop with a Mitchell Estimating system should be able to provide you with them, they may charge a fee though - that system is pricey. It'll give you a few measurements from various chassis points as well as measurements for heights of those points from a datum line. OK I will ask a few "panel beaters" with Chassis machines |
Originally Posted by FD:)
(Post 8464992)
Nah the collision repair manual is just a bunch of replacement part numbers
|
Rhino 3D FD
I've been a bit busy but i did get an Fd chassis data sheet. I just went and brought one.
I will draw it up in Rhino. Does any one else use Rhino or some other 3D drawing software? If we split the FD down the middle and a few people drew one part each (fender, door... etc..) we could draw a hole FD in no time. If we could find someone with a CMM Faro arm digitiser or even better a laser scanner arm. Once there is a 3D model it can be put through some CFD and we can get get some aero data. Glen |
Rhino 3D FD
I've been a bit busy but i did get an Fd chassis data sheet. I just went and brought one.
I will draw it up in Rhino. Does any one else use Rhino or some other 3D drawing software? If we split the FD down the middle and a few people drew one part each (fender, door... etc..) we could draw a hole FD in no time. If we could find someone with a CMM Faro arm digitiser or even better a laser scanner arm it would be even quicker and better! Once there is a 3D model it can be put through some CFD and we can get get some aero data. Glen |
Rhino 3d
I have started a page where i will put 3D drawings of the FD as I do them or as others submit them.
http://www.rx7.net.nz/rx7netindex.html go to RX7 dot net FD 3D Drawing project |
I've got some 3D modelling experience. I haven't used Rhino, but Ill be looking at at in the next little bit. I'm doing a tube frame 3rd gen road race car, so I'm as interested in the chassis data as you are. I've just started the parts pile. How could I get the data off you?
cheers, -Trent |
3d Fd
Well... I have started a site where i will put part drawings sent to me.
http://www.rx7.net.nz/rx7netindex.html go to RX7 dot net FD 3D Drawing project You just have to send me some 3D FD part drawings. I will add a list of parts required in order of importance (as far as an accurate model for track simulation is concerned) It doesn't have to be a Rhino drawing, any 3D format will do. Rhino can import just about anything. As for the Chassis drawing it's a bit hard to read. The lateral positions are OK but the vertical positions are measured using special clamps with alphabetical designations + an additional measurement. Like clamp F + 165mm + 16 mm bolt head pick-up. I need to get down to a chassis machine place and measure the various standard clamp lengths so i can work out the vertical measurements. ( I know where a machine is as I had the Chassis checked on the machine before I had the cage put in) >>I've got some 3D modelling experience. I haven't used Rhino, but Ill be looking at at in the next little bit. I'm doing a tube frame 3rd gen road race car, so I'm as interested in the chassis data as you are. I've just started the parts pile. How could I get the data off you? |
2 Attachment(s)
Post up the measurements when you have them.
I've been playing with some chassis designs in max, just sorting out ideas on what goes where. The scale is off a bit as I don't have any measurements, just ballpark guesses. -Trent |
Hi FD,
The Fd Chassis data sheet, where did you purchase this from, I'm interested in getting a copy - helpful with racecar repairs etc. Cheers, |
FD can you post the chassis data sheet.
Yes I know you paid good money for it but please realize that some of us donated a lot of shop manuals, electrical manuals to the sticky section of the 3rd Gen site. I know that I paid hundreds for what I donated in the greater interest of the marquee. |
Heh, we just go a couple of those high-accuracy Faro arms at work. One is designated as the "portable" unit. It sure would be badass to take it home for a weekend and scan points all the way around the car. Then import the data into a CAD system and scale one of those 3D models to fit the actual data and chassis spec sheets.
Unfortunately that will never happen. The dept manager is a prick and those things are like his little dicks. |
It only cost $10...
It only cost $10... I haven't looked on the forum for a while. I'll dig it out and post it up.
Originally Posted by Julian
(Post 8617865)
FD can you post the chassis data sheet.
Yes I know you paid good money for it but please realize that some of us donated a lot of shop manuals, electrical manuals to the sticky section of the 3rd Gen site. I know that I paid hundreds for what I donated in the greater interest of the marquee. |
bringing this back, has anyone completed a model for ChassisSim?
|
All times are GMT -5. The time now is 08:59 PM. |
© 2024 MH Sub I, LLC dba Internet Brands