fd3s single turbo
Hi people
I'm Joel from Portugal and I bought a rx7 fd3s single turbo, the turbo is a t4 turbo a/r.63 exhaust(i think it's little turbo for this engine), injection setup is 850cc+1680cc and FPR aeromotive, pump fuel 340l/h aeromotive, big front mount intercooler, hks ignition power, apexi power fc. The cars running very good at low/mid rpm, but when i want running more fast with boost is slow, not running fast. What's the problema you suspected? Turbo it's not good to this engine? Apexi Power fc tune not good? Sorry for my english, i hope you understand |
welcome to the board. :)
if i'm understanding what you're saying correctly, then your problem is probably your turbine. the 0.63 is too small and killing your top end. for all i know the WHOLE turbocharger may be wrong for your engine. however, you never mentioned the compressor side, so i can't comment on that. |
Sorry, 0.68AR, At this moment the turbo is temporarily, the Compressor wheel is .70A/R, Inducer: 91mm, Exducer 69.20mm, Turbine wheel: .68A/R, Inducer: 74.00mm, Exducer: 64.10mm
I have other turbo upgrade to install, it's a ball bearing turbonetics mid-frame 88mm but i hope the problema is the small turbo |
I have the next turbo to install, compressor is a/r.95 88mm inducer, exhaust is 78mm turbine and a/r is 1.15mm
http://img22.imageshack.us/img22/8651/54j6.jpg I have a stock port engine and i know it's a very large turbo and i suspected have very laaaggg, what's rpm i will go have full boost? 5500/6000rpm? :scratch: |
That turbo looks bigger than the engine! What are you plans? Drag racing?
Sent from my LG-E980 using IB AutoGroup |
Yes, it's bigger. My plans is streetracing and dragracing. I hope have a good results with this turbo :). My goal is 500hp, is possible with setup injection 850+1680cc injectors? My engine have stock porting
Any rx7 fd in this fórum with similar turbo? |
if you use the stickies to help you boost your post count, then you will be able to check out the Single Turbo forum. you should be able to get information on many cars that have similar, if not the same, setup as you plan to run.
just be sure to get your posts the right way. |
Id go bridgeport, or a 6 port with aggressive street porting to help with that power goal! Reason why I suggest a 6 port is because of this thread right here. Gives good info on 6 ports: http://www.ausrotary.com/viewtopic.p...45e2ed&start=0
Sent from my LG-E980 using IB AutoGroup |
Originally Posted by ne0tas
(Post 11600526)
Id go bridgeport, or a 6 port with aggressive street porting to help with that power goal! Reason why I suggest a 6 port is because of this thread right here. Gives good info on 6 ports: AusRotary.com • View topic - 6 PORT TURBO is it possible?
Sent from my LG-E980 using IB AutoGroup |
diabolical1
It's easy to goal 500hp with stock port, 850-1680cc injection and this turbonetics? Around 16psi... :egrin: |
Your turbine is too small, minimum I would run is a .96
You can get to 500 hp with stock ports and your fuel setup, but not with that turbine housing, that housing is going to create to much back pressure and very high EGT. But not around 16 psi, more likely 18-20 psi I would suggest you a Borg Warner S366 with a .91 housing if all you looking for is 500hp |
Oh, I totally derped. I just noticed he has an fd :P my mistake!
Sent from my LG-E980 using IB AutoGroup |
Originally Posted by JSarabando
(Post 11600538)
diabolical1
It's easy to goal 500hp with stock port, 850-1680cc injection and this turbonetics? Around 16psi... :egrin: that said, i am a little leery of you using the word "easy" in the same sentence as 500 HP Rx-7. continue your research. |
Thanks BLACK MAMBA for your information, really i think my turbonetics is more bigger than Borg Warner S366 or am I mistaken
the turbonetics mid-frame compressor housing is a/r 0.95 and exhaust housing is a/r 1.15 http://img855.imageshack.us/img855/3853/qywe.jpg What's you think about spool? 5500/6000rpm full boost? Or earlier? :scratch: |
I think a 88 mm turbo is a bit big for your 500 hp power goal, but at least you have room to grow if you ever want more power.
|
Thanks for your reply BLACK MAMBA.
After install the turbo i need tune PowerFC, after i post results. |
I'm interested to see how this works out for you, I was thinking of going to a big single myself this winter. Can't wait to see the results!
|
Serious turbo
Wow that thing is pretty big is a good thing you seem to have plenty of fuel
|
my injection fuel setup is 850cc+1680cc injectors
|
after tune i think at 1.2 or 1.3bar have good results, i hope :)
|
3rd Generation Fuel Calculator
at 85% max injector duty your fuel system is good for 650 hp at the flywheel. That is plenty of fuel for 500 whp and gives you a nice safety cushion. |
|
http://imagizer.imageshack.us/v2/280...537/p2o1w2.jpg
Turbonetics T88 mid-frame installed(sorry for little picture) :( |
The engine start and runs good at low and mid range revs, after turbo pulls the old problem continue, it's very very very slow at highs revs.
Spark plugs check, fuel filter check, vacum silicone hoses check.... Any ideas about this problem? I don't have tune to this turbo but I think isn't why don't is fast in high revs |
No tune + Lag
|
All times are GMT -5. The time now is 04:37 PM. |
© 2024 MH Sub I, LLC dba Internet Brands