street porting template
Does any body here know where I can find the largest street port template for my 13b turbo side housings. I want the most opening and closeing time as posibule with a good sized exhaust port so I will have a lot of over lap for a good lopy idle,and a nice tourqe band starting around 4000 rpm.
|
would mazda trix,or racing beat have a bigger template
|
pineapple racing has a good one.
|
yea but all they have is mild templets. I want to go big!
|
Judge Ito. I've had very good results with his template (I've used RB and Pineapple) and his by far is my fav.
|
Our circuit port template is not excessively large, but the largest you would ever want to go. Proven highest documented streetport horsepower.
|
I would suggest looking through the GG/BG threads on Judge Ito. It seems it takes a long time to get the templates for some and others it happens rather fast.
|
gto
you have any templates available for t2? |
do you have a picture of the judge ito porting templet I wasnt able to find it and how do I get one.
|
I contacted judge and he said they are 100 bucks and there is an aggresive and a not so agressive porting template the none aggresive basicly dosent open the port as early.
|
Does any body know where I can get the right bits to port with I have looked at lows, and harbor fraight, I am looking for long carbite cuting bits long round stones and sand paper rolls so I can reach those hard to reach places.
|
good luck none of those places have or can get any. racing beat sells some not 100% if they have the long ones thou. I get my stuff from work they order it form one of the Grainger Industrial Supply.
|
Originally Posted by vmarx7@yahoo.com
(Post 10920125)
gto
you have any templates available for t2? |
Originally Posted by sideways-FC
(Post 10920923)
Does any body know where I can get the right bits to port with I have looked at lows, and harbor fraight, I am looking for long carbite cuting bits long round stones and sand paper rolls so I can reach those hard to reach places.
I used this set with great success: http://www.eastwood.com/carbide-burr-set-of-four.html If you feel more comfortable and/or want a long reach set, they have that too: http://www.eastwood.com/long-reach-c...t-4-piece.html I used the burrs to port the three irons and two exhaust ports and they still look brand new, just as sharp and ready for another porting job. The Pineapple street port is also pretty aggressive IMO, especially on the primary. I was shocked how much larger they were than stock. All reports I've heard is the Pineapple ports have a nice lope to them. |
I like the BDC half bridge myself
|
does bdc have porting templates.
|
You would have to contact him, or just get the pro to do it personally
http://www.youtube.com/watch?v=FY_pY40xaVc |
Originally Posted by sideways-FC
(Post 10920923)
Does any body know where I can get the right bits to port with I have looked at lows, and harbor freight, I am looking for long carbite cuting bits long round stones and sand paper rolls so I can reach those hard to reach places.
pineapple has a large street port for the 13bt, I called him and he stated to order the brew and put in the notes that it is for a 13bt, i also ordered the epa3 exhaust template. he is really helpful! I will be ordering from him again! as for the porting tools, I got everything from harbor, 1/4 electric die grinder $30 a few packs of stones $3 and a large pack of 80 grit cones for $21. you do not need the expensive bits, maybe if you were porting multiple irons and or heads, the stones and drums listed here are more then enough. I also used my dremel for the more critical areas and the touch up, here is a almost done picture of my center iron.. runners are done but the face has not been ported. critics are welcome http://www.facebook.com/photo.php?fb...1&l=fed14c4772 grinder http://www.harborfreight.com/electri...aft-44141.html cones http://www.harborfreight.com/52-piec...set-96826.html stones http://www.harborfreight.com/5-piece...set-94992.html I just started porting a few days ago and got a lot better result then I expected, i read the reviews on the grinder and had a lower expectation... but is a lot better than what others make it seem to be.. |
well I do need the sand paper rolls yet I found the carbite bits on amazon all I need is a ball stone yet. I like the carbite cuting bits they take the matel away like its butter and they do it super smooth. I like the air powerd die grinders. I have a bunch of junk housings I have been practising on.
|
does any body know if judge ito's porting template moves the opening of the port beyond where the the side seal tip rides?
|
Originally Posted by sideways-FC
(Post 10951089)
does any body know if judge ito's porting template moves the opening of the port beyond where the the side seal tip rides?
|
yea I saw one of your threads on the other forum talked about tapering the closing edge of port so the side seal dosnt catch the edge when you port past where the side seal rides. thats why I wonderd if your port went past that.
|
Originally Posted by sideways-FC
(Post 10954998)
yea I saw one of your threads on the other forum talked about tapering the closing edge of port so the side seal dosnt catch the edge when you port past where the side seal rides. thats why I wonderd if your port went past that.
|
All times are GMT -5. The time now is 07:40 AM. |
© 2024 MH Sub I, LLC dba Internet Brands