RX7Club.com - Mazda RX7 Forum - View Profile: andre sinclair

andre sinclair andre sinclair is offline

Rotary Freak

About Me

  • About andre sinclair


Total Posts
Visitor Messages
Total Likes
General Information
  • Last Activity: 05-19-19 11:11 AM
  • Join Date: 01-18-02

Visitor Messages

Showing Visitor Messages 1 to 10 of 18
  1. andre sinclair
    04-16-17 03:18 AM - permalink
    Ok. Give me your number and I I'll ring you tomorrow
  2. 04-14-17 10:36 PM - permalink
    Hey. I am interested in the pair of new s5 rotor housings you have. What price can we agree upon? I am locate in Miami so I can pick them up. Thank you also interested in a few other items
  3. andre sinclair
    01-13-14 08:02 AM - permalink
    Bump start,

    Thanks for your response. I've confirmed the timing the T1 plug, stock pin to mark indicate 20 ATDC (15 degree split across the board/all rpm and all timing trim including static is set to zero). However, it still showing me 65 degree on the L1 timing instead of the 5.

    How do I check to see if it's firing in waste spark mode?
  4. bumpstart
    01-11-14 08:28 PM - permalink
    sure its not a FC program in it? does the ID screen say 13bt ??

    ......time it using the t1 plug , the stock pin and mark on FD is 20 ATDC

    ..screen 26 leading /trailing split at idle and low revs set to 15

    and all timing trims set on zero

    by timing the trailing correctly , leading should automatically be 5 ATDC

    .. but cause you may have it firing the stock leading coil then it will be wastesparking and you cant read the timing pulse on some lead/ light combos on one of the spark plugs
    ( cause the wasted spark on one rotor is actually heading from chamber to the coil..)

    also/// if the ecu has 4 ignition outputs ( put is running the stock leading coil /ignitor ) then you may have to wire both leading output wires to the ignitor
    ( else it has to be configured by microtech .. and its hard to call what is what as some units are simple 3 output setups for stock coils,, and others are setup as four ig outs for the x4 box )
  5. 05-20-12 10:23 PM - permalink
    This is an intriguing topic. Nike OutletsI’m always looking for valuable resources to show clients and my coworkers, and your article is definitely worth sharing!Keep up the amazing work!! I love how you wrote this and I also like the colors here on this site.Oakley Outlets did you create this yourself or did you outsource it to a coder??
  6. romo
    04-14-11 03:24 AM - permalink
    I replaced the covered dash with a cherry original one...I am going to try to remove the cover if i am successful I can sell you the cover cheep...If you are interested let me know. ROMO
  7. 04-03-11 07:58 AM - permalink
    do u still have the epsilon rims for sale
  8. jujubing
    08-01-10 01:26 PM - permalink
    nice setup man.. am gonna do the same swap on my 83 but i was wondering if u can help me out w some info on the cradle u made for the motor mounts.. any info would help man. very nice setup once again!
  9. mikeric
    05-21-10 07:29 AM - permalink
    I just put a Mariah WB on my SE. I liked the way your wheels sit flush. Would you mind sharing the specs with me?
    09-12-09 08:10 PM - permalink
    Nice rides bro!

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.