wide front fenders & stock rear
Hey everyone, when i purchased my car it came with 18" rims up front. Someone had attempted to roll the fenders, and did a poor job, you can see where the rubber has actually caught the lip before, and the lip is now all rusty.
This project is probably for next winter, as i want to enjoy driving it this summer and not have it under the knife. But I want to keep my eye out for good deals in the mean time. My question is, if I find a good deal on wide front fenders, does it look ok without adding flares to the back? I may just get mine fixed, but I would guess it'd cost like $400. So if I found good used aftermarket fenders for cheap, I could just get them painted and be ready to roll. Please don't flame haha, i just want to see if its been done, what it looks like, and theres a good chance i may just keep it stock. |
Visit the Shine Auto project section under vendors, great product! Costs a bit more all said and done but at least it will cure your rust issue.
https://www.rx7club.com/shineautoproject-161/fd3s-feed-type-ii-r-front-bumper-feed-sides-571409/ Front Fenders 25mm wide $450 Pm me for shipping prices. Ads by GoogleBuy Body Kit Direct Front Bumper, Side and Rear Bumper Pick Up or We ship to you visracing.com This ad is not displayed to registered or logged-in members. Register your free account today and become a member on RX7Club.com! __________________ Shine Auto Project, Inc. 9135 Santa Anita Ave. Rancho Cucamonga, California 91730 Paypal/Email: To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. Tel: (909) 980-3433 Fax: (909) 980-3833 |
Doubt it. You can get stock fenders very inexpensively. If the problem is only on the inside of the fenders, get some roll-on / brush-on undercoat paint, clean up the rust and seal it with the paint. If it is visible, then you have more expensive work ahead of you where you may need some professional painting.
|
The lip is all bent and the rust is visible. It's definitely in need of a professional job. I'd love to go with the shine above, but the only reason I was looking into this is because once in a while I see used wide front fenders in the FS section for pretty cheap.
But I don't want to go through all the trouble of matching it with rear fender flares. Then I'd need wider rims in the back to make it look good. And thats much more than I'm willing to spend. I do want to update the front bumper at some point, but I'm not sure if any wider aftermarket front fenders fit a front end that is a stock replacement (i.e. non widebody) |
I've seen FEED wide front fenders with stock rears...it looks fine to me.
http://www.yokohamatire.jp/yrc/japan.../de_car_02.jpg |
I have Burnout wide front fenders from Ken at Shine Auto. When I installed them they look funny with the stock rear so I got the Burnout rear fenders too. Search my name and you can see some pics of my car with just the fronts on.
|
Originally Posted by Funkspectrum
(Post 9209450)
I've seen FEED wide front fenders with stock rears...it looks fine to me.
http://www.yokohamatire.jp/yrc/japan.../de_car_02.jpg If there are no cons, I might seriously consider this set-up on my car as it'll be totally reversible since no rear fender molding involved. |
2 Attachment(s)
Originally Posted by Alpsta
(Post 10221945)
Does anyone know if this will have negative effect on the handling of the car? Wide front fenders will require either wide wheels or spacers to fill the gap which will increase the front track. Is it going to increase oversteer?
If there are no cons, I might seriously consider this set-up on my car as it'll be totally reversible since no rear fender molding involved. Attachment 721326 Attachment 721327 |
^ WAIT!!! When did you get rims. That looks so much better than the stockers.:icon_tup:
Needs more low... But in the city I can see why that is not possible:( John |
there is now stain on my carpet, thanks a lot.
|
Originally Posted by 2RotorsNaDream
(Post 10222085)
I run wide front fenders and stock rear fenders and it looks fine. Just get some low offset wheels nice and flush and itll look good and even. I run 18x9.5 +15 in the front and 18x10.5 +25 in the rear and I have no handling issues.
|
Originally Posted by RENESISFD
(Post 10222161)
^ WAIT!!! When did you get rims. That looks so much better than the stockers.:icon_tup:
Needs more low... But in the city I can see why that is not possible:( John
Originally Posted by KKMpunkrock2011
(Post 10222185)
there is now stain on my carpet, thanks a lot.
Originally Posted by Alpsta
(Post 10222567)
As Barney Stinson would say "awesome" :icon_tup: That's what I was looking for. What size tyres are you running?
|
Originally Posted by Alpsta
(Post 10221945)
Does anyone know if this will have negative effect on the handling of the car? Wide front fenders will require either wide wheels or spacers to fill the gap which will increase the front track. Is it going to increase oversteer?
If there are no cons, I might seriously consider this set-up on my car as it'll be totally reversible since no rear fender molding involved. Rear: Extending the track will cause the diff to "tighten up" more easily. This would be most noticeable when the rear starts to skip when making sharp turns i.e. making a turn at an intersection. It will also effectively "soften" the springs. On an FD, you'll start noticing these effects if you decide to push the wheels out 50mm or more... which I don't recommend. The car will handle more poorly and really be less fun to drive.
Originally Posted by 2RotorsNaDream
(Post 10222085)
I run wide front fenders and stock rear fenders and it looks fine. Just get some low offset wheels nice and flush and itll look good and even. I run 18x9.5 +15 in the front and 18x10.5 +25 in the rear and I have no handling issues.
When I was running 18 x 10 +22 rears, I also noticed skipping during (intersection) tight turns, not a big deal, but I'm sure my diff didn't like it. |
^
|
Thanks Josh. I don't know why a reputable company like Feed does it though, since they have the option to fit a rear fender if they wish.
Eitherway, I'm keeping it stock body and if I ever go widebody I'll do rear fenders as well. |
All times are GMT -5. The time now is 04:23 AM. |
© 2024 MH Sub I, LLC dba Internet Brands