In his setup like in my, have TWO types of injectors!!!! In ecu you may choice only both high or both low!!!!

measure difference of low and high injectors and buy an any shop for electronic components resistor size you measured

If you have a combination of high and low impedance set the ECU up for low impedance. There is no degradation of performance running a high impedance injector in peak and hold mode. There is a degradation in performance by running a low impedance injector with a resistor.

!!!!!

what guarantees that ECU or injectors did not damage!

Injector Current Control
The injector drivers in the ECU are capable of operating both saturation and peak and hold mode injectors. Injector current is monitored by the ECU and will be adjusted automatically.

The Injector current control has two settings, which relates to the resistance of the injectors used.

1 - 2 Ohms: This setting is for motor sport injectors with a resistance equal to or less than 2 Ohms.

2 - 14 Ohms: This setting is for all other injectors having a resistance greater than 2 Ohms.

Please note that using the incorrect setting may cause poor operation or damage to the injectors and/or ECU.

oops! That info is not for a E6X..

in haltech as i remember
1) 1-4
2) 4-8
3) high

If you're running a high impedance injector in peak and hold mode, the injector is not capable of drawing more amps than the ECU can support. No way to damage the ECU. Since the injector will only draw as many amps as it's impedance will allow, there is no way to damage the injector.

Do it however you feel comfortable. You'll get better injector performance if you run without resistors though.

probably you right.

but why in haltech you must choice 3 types? 2 types of PaH and one High. What difference?
4/1 driver and 2/0.5?

with ohm law i understand that the high imp injector not get more amps. but im not understand how work driver in ECU if it in PaH mode

can anybody help with S4/S5 Streetported ignition maps?
i have EGT - 878F on 1200rpm. is this normal?
and what Air-fuel ratio must be on idle? 1200rpm? with 750cc injectors?

Wanted to know if you could help me out with a basemap...

1. 1986 FC3S
2. 13BT Jspec (S4), race ported, with the FD's UIM
3. OEM Jspec turbo
4. Haltech PS1000 13BT Kit
5. Walbro 255 fuel pump
6. Stock 13BT injectors and fuel rail
7. Stock fuel pressure regulator
8. Custom v-mount setup (Mid-Large Sized) (2.5 IN in-out intercooler)
9. 3 IN downpipe, 2 1/4 Dual exhaust with only 2 resonators, no cats
10. 3 IN intake with cone
11. LS1 coils (4 of them) MSD ignition wires
13. Stock ignition, CAS, and spark plugs
14. Using the MAP sensor built in the PS1000

Currently attempting to use the attatched basemap to get it fired and it isn't working...
http://dl.dropbox.com/u/15220027/RX-...0coils.hs1-106

Anybody have a PS1000 base map for a 87 S4 TII? Stock everything.

Need a base map for my setup please.

'87 TII
Stock port 13bt, with 2mm cryo RA seals/race springs
stock S4 turbo/deleted twin scroll actuator
550cc/880cc injectors
stock coils
gm coolant temp, IAT, and 3 Bar Map.
Walbro 255lph

just need a base map to get it running, and check for leaks. would help a ton as i have to load it onto trailers this week, and get it to Cali to get it tuned. would suck pushing it around.

anyone??? would like to get my car mobile. any help would be rad. searched for a bit, but as we all know, there's alot of broken links that don't work anymore... please point me in the right direction atleast.

Nevermind. Got it tuned at UMS in Phoenix. :icon_tup: 183 whp. did I mention it was stock? :nod:

hi there anyone have a map for a 93 rew street ported,ps1000,4-1680,stock Tll coil,and cas, holset turbo,any one can help me out on this. thank's if you need more info please let me know

umm does anyone every get any maps as it seems that alot of people asking for maps.. ive asked a few times and had no response from members.. :(

still haven't received one. there's maps in Claudio's other thread, but nothing works. i've done the right click/save as technique, and it does work that way, i just don't have a computer to support it.... waiting on a tuner still, and lack of support really sucks when you want to drive your car....

Hi im looking for some kind of starter map.
90 s5 na
Haltech e6k
Innovative wideband
Stock fuel everything(pump, injectors, and rails)
Stock coils
Stock ports except 5th & 6th ports welded open.
RB header to 3inch all the way back.

ok, here is a tought one (or at least i think so)
Haltech E6K, sa22c 12a (with the big centerports) FDintake with FDinjectors and stock FDpump
stock FCleading coil and msd blaster2 on trailing. FC CAS and t2 turbo.
got anything i can use?

Hey guys.
I need a map for an S4 TII with 750/1000's,Modded throttle body,BNR stage 3 turbo,3 inch RB exhaust,,
Platinum 1000 is the ECU.

Haltech E8

S5 Small Half Bridge
FD UIM & TPS
GM Coolant and Air Temp Sensors
Holset HX52 Turbine
3 1/2 dowpipe and exhaust
Hks 40mm wastegate and manifold
550s primary 1600s secondary
LS1 Coils (Direct Fire)
FMIC
3 Bar GM Map
______________

Just installed a platinum 1000 in 93 FD.
Running 4 id2000, 3bar map, billet67. Does anyone have a decent base map just get get this car fired up. I can handle fuel and timing just new to haltech ecu.

Need P2000 basemap for 20B Rx8 Garret GT40, 850/1680, autronic 500RCDI, LX92 coils
funklove@gmail.com

ls1 coils as well.:)

need a base map to get the car to get tune
93 fd stock block, 2000 hi secondary, 1000 hi primary,sprint re, single turbo gtk 850, ac and ps, no cats, rb exhaust , vmount intercooler, fpr set at 40lbs, internal map from sprint re. please email it to me. thank you