I like the roll cage gussets... :)
|
|
keep killlen it
|
im gonna have to compression test my motor today.
leaving the event, it flooded out, and wouldnt start...towards the way home, it started mis firing, and seemed as if theres a stuck corner seal/side seal... today i drove it around for a bit, and it completely fell apart. im hoping like whoa that its just a coil pack, harness, shitty TPS, or something minor, but with my luck i know it'll be blown... |
Originally Posted by red92vr4buckey
(Post 9876697)
im gonna have to compression test my motor today.
leaving the event, it flooded out, and wouldnt start...towards the way home, it started mis firing, and seemed as if theres a stuck corner seal/side seal... today i drove it around for a bit, and it completely fell apart. im hoping like whoa that its just a coil pack, harness, shitty TPS, or something minor, but with my luck i know it'll be blown... |
i hope so... every now and then it'll kick, and it'll fire right but its like full throttle blips, above 4500...
im so bummed i havent even fucked with it... the next event is 2 months away and my broke ass has no job.... |
Originally Posted by red92vr4buckey
(Post 9877242)
i hope so... every now and then it'll kick, and it'll fire right but its like full throttle blips, above 4500...
im so bummed i havent even fucked with it... the next event is 2 months away and my broke ass has no job.... |
a little delayed update...
since the last event, i pulled the motor stripped the engine bay, and took it to forest's new shop out here to have him stitch it up. picking it up tomorrow and have to start painting it. bought new BN from him, got a supermade hood vents for my NA aluminum hood. the motor has been apart for a few weeks. ordered an atkins kit with RWS water seals/gaskets. the rear rotor took a shit. the timing was firing dead on the apex seals almost... one broken apex seal, and a cracked front iron water passage. got the rebuild kit/rotor/iron/housing from my sponsor EAM/area77rotorworks. theyre putting it back together with a small streetport, but opening up the exhaust ports a shit load. got an oldschool TRUST 3"Downpipe, rear camberbar. had forest make me some spindles to get nutty angle... still need to pay for that shit though... lol fucking taxxed out for money right now... still need over fenders and tires, and a standalone... if this motor blows im letting forest source me an SR and we're fabbing that shit up. pics tomorrow when i pick it up. hoping to make the XDC vegas event may 22nd. |
SR's aren't any better... the head set up/rockers are probably one of the worst designs for high rpm applications...
Rotarys are not good if you aren't doing everything the right way at once... but if you spend your money the right way, they are pretty reliable race engines. Good luck, anyways. |
Was forrest all phazed when you saw him?
|
Originally Posted by USS CJ
(Post 9954540)
Was forrest all phazed when you saw him?
fucker is OG. i got the car back yesterday, dropped off my spindles. poor mike's car is all piled on the wall of shame.... he totalled it bombing top of 3rd at a vegasdrift event. his new shit's gonna be sick. forrest is getting all nutty on the track car for xdc shit's mental. |
Originally Posted by davedge
(Post 9954112)
SR's aren't any better... the head set up/rockers are probably one of the worst designs for high rpm applications...
Rotarys are not good if you aren't doing everything the right way at once... but if you spend your money the right way, they are pretty reliable race engines. Good luck, anyways. this is already motor number 5 in 3 years. i've only done 10 events or so, but street drove for like a year. this is my last attempt. hell RB, 1j/2j, anything but LS... im just getting burnt out on sitting out and not driving... |
SR's are great if you put solid lifters and better springs in them.
I've been reading up that the rocker arm stoppers will cause the rockers to break vs just falling off. My vote goes to 1j but you can play with an sr and still have it reliable if you put the coin towards reliability but you already know this. |
Originally Posted by NoPistons!
(Post 9957663)
SR's are great if you put solid lifters and better springs in them.
I've been reading up that the rocker arm stoppers will cause the rockers to break vs just falling off. My vote goes to 1j but you can play with an sr and still have it reliable if you put the coin towards reliability but you already know this. i just get so bummed when forrest and all my other SR friends tell me they're motors are like 5 yrs strong and shit... forrests shit will hop a rocker maybe once or twice a year, but he drives the shit out of it, and does a gang of events/street driving... alll these rich ass kids here have fully built 13's, and 14's, and they have stock SR's that bust.... my friend phil has had his SR with a 2871R for 5 years.... shits more nuts than forrests street car sometimes. |
the motor was/is still in stockish form?
good inspiration man keep it up. |
What was the total weight of dry icing the tar out? My buddy did his FC, weighed it, and it came out to 100lbs.....
|
Originally Posted by red92vr4buckey
(Post 9957026)
i know... what i meant more or less is im not getting 7 motors into this shit.
this is already motor number 5 in 3 years. i've only done 10 events or so, but street drove for like a year. this is my last attempt. hell RB, 1j/2j, anything but LS... im just getting burnt out on sitting out and not driving... |
Originally Posted by laramiejoe
(Post 9965028)
You're doing something wrong. What's your engine set up like? Stock turbo?
this car never had a wideband, never got timed, completely stock, minus an FCD, 3" DP, straighpipe... etc. had stock injectors and boosting at 10-14lbs when i'd upshift 3rd but would usually chill at 9ish, snipped wastegate line, and i just railed on it.... i beat the hell out of it. my friend timed it (hes been building crazy motors for a while) just did it by sound... it was fast, but also sped up the process of it dying. either way its whatever. the new motor is built. im buying a haltech, and making sure this one lasts cause i like the motor's. just sucks not driving and spending money that i dont have.... |
Originally Posted by Scrapp
(Post 9964227)
What was the total weight of dry icing the tar out? My buddy did his FC, weighed it, and it came out to 100lbs.....
the shop vac was heavy as fuck though when i did the entire front area. |
Chassis paint -
http://i76.photobucket.com/albums/j1...e/IMG_0791.jpg http://i76.photobucket.com/albums/j1...e/IMG_0792.jpg Crazy cage spray paint http://i76.photobucket.com/albums/j1...e/IMG_0793.jpg http://i76.photobucket.com/albums/j1...e/IMG_0799.jpg Fresh BN from Forrest http://i76.photobucket.com/albums/j1...e/IMG_0796.jpg http://i76.photobucket.com/albums/j1...e/IMG_0797.jpg finished product, ready to be put back together. the miracle's $100, some time, and rattle cans can do to your car... http://i76.photobucket.com/albums/j1...e/IMG_0804.jpg http://i76.photobucket.com/albums/j1...e/IMG_0805.jpg More to come tomorrow in the light. need to see the crazy pearl flake. plus i should have it almost done late tomorrow, with everything else painted, and in. more pics to hold you over till then: the motor/drivetrain: RWS seals, water jacket seals, fresh rotors/housings, and a new front iron. http://i76.photobucket.com/albums/j1...e/IMG_0803.jpg http://i76.photobucket.com/albums/j1...e/IMG_0802.jpg so i can blow up tranny's: http://i76.photobucket.com/albums/j1...e/IMG_0801.jpg will post more tomorrow in the daylight. "we're" ready. the sleepless nights begin! |
The daily bomber. build thread to come soon:
http://i76.photobucket.com/albums/j1...e/IMG_0794.jpg http://i76.photobucket.com/albums/j1...e/IMG_0795.jpg |
how many fc's do you have? I count 3 lined up! Holy shit.
|
Originally Posted by red92vr4buckey
(Post 9966070)
i know... this time i got lucky for it lasting as long as it did...
this car never had a wideband, never got timed, completely stock, minus an FCD, 3" DP, straighpipe... etc. had stock injectors and boosting at 10-14lbs when i'd upshift 3rd but would usually chill at 9ish, snipped wastegate line, and i just railed on it.... i beat the hell out of it. my friend timed it (hes been building crazy motors for a while) just did it by sound... it was fast, but also sped up the process of it dying. either way its whatever. the new motor is built. im buying a haltech, and making sure this one lasts cause i like the motor's. just sucks not driving and spending money that i dont have.... |
Originally Posted by laramiejoe
(Post 9966620)
If you wanna be cheap, you can get your ecu chipped, run 850cc secondaries, and get a boost controller and be fine. The trick to stock ecu is big secondaries, and you have the best ecu because it's an '87 so it uses low impedance injectors. Haltech would be best though.
we'll see how it goes. i appreciate the help. i'm really hesitant to try new setups on my motors cause for one, i hardly have the cash to do it, and for two it always results in killing a motor and now we have a grand tied up in my new keg.... i dont want to kill it...<- the motor. lol joe, seriously your car is the shit btw. |
All times are GMT -5. The time now is 07:17 AM. |
© 2024 MH Sub I, LLC dba Internet Brands