White 1987 GXL Build {Lots of Pics}
Welcome all to my little spot on the inter-web. Say hello to Becky…..she’s my white girl, LOL! (^_^) She is my second…2nd Gen Rx-7…. it’s a 1987 GXL. Bought her from some kid with pricings in February. From looking at it this kid did not know what he was doing with this thing, although he had three of them in his mom’s garage, including a turbo that from the looks of it was set up to drift. The car came with a 5-speed swap that wasn’t complete (-_-). The seller “said” the car was driven by a college girl and was never raced…… but as you can see the car came with a RB race header to glass pack to 4.5” fart can! (O_o)
Also the AC was removed and air pump was disconnected……never raced I highly doubt it. http://www.norotors.com/MGalleryItem.php?id=3181 The car had some problems that he couldn’t fix (hard start, 3800rpm hesitation, random surging, and electronics) First week added the grounding wires explained in Aaron Cake’s web site(http://www.aaroncake.net/RX-7/grounding.htm) and set the idle. It became a daily driver. http://www.norotors.com/MGalleryItem.php?id=3221 http://www.norotors.com/MGalleryItem.php?id=3182 http://www.norotors.com/MGalleryItem.php?id=3183 http://www.norotors.com/MGalleryItem.php?id=3184 http://www.norotors.com/MGalleryItem.php?id=3187 A couple visit to forum member Fong’s super garage sale in MD and I had a under tray, rear speaker covers, ash tray, Bomez dual exhaust (to pass emissions), s4 lip, radiator shroud. http://www.norotors.com/MGalleryItem.php?id=3220 http://www.norotors.com/MGalleryItem.php?id=3964 Hid retrofits from forum member TurboIIrotary http://www.norotors.com/MGalleryItem.php?id=3969 Reconnected the air pump, new alternator belt, and some fuel cleaner….. She passes emission in DC on the first try! Next got some stainless steel oil cooler lines. http://www.norotors.com/MGalleryItem.php?id=3965 |
Zankoku Performance coilovers which are 12/10 - 16 way adjustable…..Can you say Stiff hard ride!!!! Plus Prothane bushings, Suspension Techniques rear sway
http://www.norotors.com/MGalleryItem.php?id=3961 http://www.norotors.com/MGalleryItem.php?id=3959 http://www.norotors.com/MGalleryItem.php?id=3967 http://www.norotors.com/MGalleryItem.php?id=3968 Rear strut bar http://www.norotors.com/MGalleryItem.php?id=3960 New Optima yellow top ……Got rid of the sucky 205/40/17 ……. and got some 225/45/17’s Next was a nice brake master cylinder brace from Zero Level Motorsports http://www.norotors.com/MGalleryItem.php?id=3958 Also the air filter broke http://www.norotors.com/MGalleryItem.php?id=3955 So I replaced the plastic adapter with a metal one and smaller filter. http://www.norotors.com/MGalleryItem.php?id=3956 Angry Bird Security!!!! http://www.norotors.com/MGalleryItem.php?id=3953 This is how she sits now awaiting new inner tie rods and the angle kit from mazdatrix.com. http://www.norotors.com/MGalleryItem.php?id=3957 I also have a new clutch kit from mazdatrix, new pilot bearing and seal, new stainless steel/hard clutch lines, new master and slave cylinder, rear trans seal, and throw out bearing for the 5 speed swap. Just need to get a lightweight flywheel and manual starter. http://www.norotors.com/MGalleryItem.php?id=3962 Thanks for looking. I have a lot of more photos but this will do for now. |
looking good. more low and new rims and ur set.
|
not a bad build so far. never heard of zokoku coilovers......i wouldent trust off brands like that
and you need some real wheels other than that, keep it up Lloyd |
Originally Posted by Celestial-Fc
(Post 10878966)
looking good. more low and new rims and ur set.
Originally Posted by magus2222
(Post 10878989)
not a bad build so far. never heard of zokoku coilovers......i wouldent trust off brands like that
and you need some real wheels other than that, keep it up Lloyd Im trying to do quality name brand parts, and these had good reputation on the forums. Any suggestions on parts are appreciated. I have Karack's adjustable rear toe bar coming in sometime this week as well. |
oh, well, i stand corrected. and 12/10 is massively too stiff, my zeals are 8/6 with proper valving, and i got a damned good deal on them lol.
anyways, keep it up Lloyd |
Thanks... but we will see about these Zankoku's, they may be good for supras but the rx-7 is a different animal as we all know ;-). Right now its a daily driver withe some drifting on the weekend once the 5-speed goes in. By the way can I haz your seals Plezzzzzzzzz!
|
I mean seats*
|
what seats? my infini seats? np, 1750 shipped
Lloyd |
:tear: Wait, are you saying it's not going to be a X-mas gift?
|
Considered putting the fan shroud back on?
|
Originally Posted by dwb87
(Post 10879333)
Considered putting the fan shroud back on?
I also came home early today and look what was waiting for me! :bigthumb: https://www.rx7club.com/picture.php?...ictureid=42094 |
Update:
This weekend a lot happened….. First one of my teams drift car has ate a carrier barring that cost more than getting a new aluminum ::In my Jeremy Clarkson Voice:: drive shaft. Since he is a broke B#$% I agreed to buy his Aluminum drive shaft if he does work for me. Only because I have more parts than time to put them on :( Trans swap….. 5 speed and driveshaft http://www.norotors.com/MGalleryItem.php?id=3983 New Master and slaves from Autozone http://www.norotors.com/MGalleryItem.php?id=3984 http://www.norotors.com/MGalleryItem.php?id=3986 New Maxdatrix angle kit, new inner tie rods new fuses,….etc. http://www.norotors.com/MGalleryItem.php?id=3987 My friends 1987 supra MKIII with A 1uz-fe V8 Swap…. I’m doing the wiring later, but right now is awaiting a drive shaft. http://www.norotors.com/MGalleryItem.php?id=3989 GET TO WORK B@#$^ :bottom: http://www.norotors.com/MGalleryItem.php?id=4009 |
Removing the old inner tie rods
http://www.norotors.com/MGalleryItem.php?id=3992 http://www.norotors.com/MGalleryItem.php?id=3994 http://www.norotors.com/MGalleryItem.php?id=3995 Outer tie rod end was done! :icon16: http://www.norotors.com/MGalleryItem.php?id=3996 Oh my god the angle!!!!! But this is without the tie rods :D http://www.norotors.com/MGalleryItem.php?id=3997 Installed mazdatrix rack spacers and bumpsteer http://www.norotors.com/MGalleryItem.php?id=3998 |
http://www.norotors.com/MGalleryItem.php?id=3999
http://www.norotors.com/MGalleryItem.php?id=4000 After tightening the bolts down I found out the angle kit is coned at the bottom and I have about 5-8mm if space before its flush with the knuckle…. I will ask the drift nuts about this later. :scratch: http://www.norotors.com/MGalleryItem.php?id=4002 Almost done! http://www.norotors.com/MGalleryItem.php?id=4003 New angle…. I do hit something but I think it’s the sway. I will make the sure after the alignment. :icon16: http://www.norotors.com/MGalleryItem.php?id=4005 Just a reminder we had to grind down a pair of vice grips to tighten down the inner tie rods like in the tutorial in the archive section. http://www.norotors.com/MGalleryItem.php?id=4008 Although I had a lot more parts I need to put on I did not have a chance to do it. Like Karack’s Camber link, prothane bushings, repainting the side moldings, relocation of the license plates and maybe cutting the front bumper. :( I guess it will have to wait for another weekend. |
nice stuff.,.
|
Originally Posted by R-X-R
(Post 10888367)
nice stuff.,.
So I took my car to the alignment shop and they couldn’t align it. Went to the Drift set-up thread and found out to get a 0 toe I have to cut some threads off the inner tie rod. I guess I'll be taking my cutter to the tie rods....:Kill1: Also since I don’t like the way the outer rod fits on the knuckle I'll take my drill to it! :icon16: |
looks good. you are probably hitting the front strut bar.
most of the drift guys(including me) just ditch both sway bars. the spring rate on the coilovers is enough to make the sway bars not very effective anyway. |
Thanks, made a U-turn this morning and got some metal on metal grid :hah: .... so I think your right. I'll ditch it tonight or tomorrow.... right now its raining so we will see.
|
Update:
I finally got a chance to install the Karack’s camber bar this weekend and it is a great product. I had no problems with install or fitment. Adjustability was as simple as jacking the car up and unlocking the bar (two nuts) then adjusting, and then locking the bar. https://www.rx7club.com/picture.php?...ictureid=42389 https://www.rx7club.com/picture.php?...ictureid=42407 https://www.rx7club.com/picture.php?...ictureid=42391 Can’t really tell from the photos but the new camber link is about 1 inch shorter than stock. https://www.rx7club.com/picture.php?...ictureid=42392 I also took off the front sway bar but didn’t get a chance to cut my inner tie rods down due to not having enough time. Sorry guys I have more parts than time I have to put them on so they are kinda just laying in a pile in the house. Sway bar end link were shot anywas… :icon16: https://www.rx7club.com/picture.php?...ictureid=42394 |
The wheels still rub the inner fender… I guess I’ll take a hammer to it. :icon16:
https://www.rx7club.com/picture.php?...ictureid=42404 While taking off the front strut bar one of my coilover studs broke off the coilover and now just spins in the hole….damn-it :cursing: :wallbash: https://www.rx7club.com/picture.php?...ictureid=42397 I have a small problem though, when I have the car on and I’m just sitting still after about ten minutes small amounts of smoke come up from the hood. I thought it was my exhaust…. Re-sealed it. Then I thought it was the front sway bar getting hot and burning the under hood shielding. Took off the front sway, but smoke still comes. Looked over the PD and didn’t see any fuel, but I have a banjo bolt for that. :wtf: https://www.rx7club.com/picture.php?...ictureid=42398 https://www.rx7club.com/picture.php?...ictureid=42399 Any thoughts? |
Side note: The aluminum drive shaft came for the V8 Supra!
https://www.rx7club.com/picture.php?...ictureid=42400 Sheba doesn’t trust it… https://www.rx7club.com/picture.php?...ictureid=42401 https://www.rx7club.com/picture.php?...ictureid=42402 https://www.rx7club.com/picture.php?...ictureid=42403 :asian: Nozzz!!! https://www.rx7club.com/picture.php?...ictureid=42406 https://www.rx7club.com/picture.php?...ictureid=42405 After driving the car this weekend removal of the front sway and strut bars has soften my ride a bit, and with the rear end being tight up and starting to premix the car seems to want to be driven faster! |
get to work brandon this becky of yours still has a long way to go ... needs more low:D
|
Taka I'd knew you'd find your way here :suspect: You know good and well I can"t go lower because of the exhaust. Besides should you be trying to make that damn supra work....:gwink: Been down for a min. Sir :rofl:
|
lmao i drove it back to school today. the driveshaft works flawlessly btw and so to the tension brackets i made.
now back to becky, just ditch the crappy piping or let me cut and re weld it so it hangs higher either way you still NEED MORE LOW :D |
All times are GMT -5. The time now is 05:38 AM. |
© 2024 MH Sub I, LLC dba Internet Brands