super darkside 85’ widebody turbo car :-)
Been a while since I've been on any forums but I'm back just wanted. To share my build with you guys. I've had the car since I was 14 imm 27 now... I've had countless rotard motors both efi and carbed NA and Turbo you name it I've done it. As of right now my 'baby has: Engine/drive train Lt1 engine out of a 95 comaro T-56 six speed with act clutch and pressure plate(6puck unsprung) Pro 5.0 short shifter Willwood master, slave -4 braided Teflon press fit hose Impss intake coupler Wrx intercooler Stainless custom exaust manifold and stainless to the back of the car. HKS 40 mm waste gate Blitz bov with wrx adaptor Custom fuel rails -10 feed -6 return 14 gal aluminum fuel sumped cell with fuel foam -10 feed from tank to rail all SS braided Teflon lined and -6 return. Aerimotive tsunami 750 inline fuel pump with aerimotive a1000 filter Aerimotive 3130 RRFPR ADJUSTIBLE Xs power. 85 rear. 58 compressor cold side Turbo t3 Tunnercats tuning software
Body 3rd Gen knightsport front nose Imsa wide body Mariah rear apron and side skirts 2nd Gen flush headlights (hacked up to fit) H3 HID kit Quad Headlamps Shaved door. Handles Escargo' hood :-) lol Audi a4 side marker lights Interior MOROSO procomp 8 point cage Moroso cage foam New drivers side floor pan... long story... FD 94 black suede seats Custom seat rails Sparco four point racing harnesses Interior painted black with metallic flake New carpet Blue point fuse box Optima mounted behind pass seat. HUMONGUS MIRROR:-P Carbonfiber dash (getting painted now) out of an 83 Custom gauge cluster with autometer tach and do gauges Switch pannel that goes in the main vents with blitz Turbo timer Sparco pedals Sparco wheel I'm sure there is more but I can't think of it. There are more parts getting added dayly lol Excuse my spelling it SUCKS not to mention I'm typing on my tablet... Pix they are not up to date they range from 3 mo to 2 weeks.... I have my body guy working on it every Sunday... he's the recan dude in one of the pix. http://i911.photobucket.com/albums/a...o/IMG_0372.jpg http://i911.photobucket.com/albums/a...o/IMG_0363.jpg [img width=800 height=597]http://i911.photobucket.com/albums/ac317/rx7pro/IMG_0359.jpg[/img] http://i911.photobucket.com/albums/a...o/IMG_0374.jpg [img width=800 height=597]http://i911.photobucket.com/albums/ac317/rx7pro/IMG_0354.jpg[/img] http://i911.photobcket.com/albums/ac...o/IMG_0356.jpg [img width=800 height=597]http://i911.photobucket.com/albums/ac317/rx7pro/IMG_0306.jpg[/img] These two were taken today http://i911.photobucket.com/albums/a...ro/photo-2.jpg http://i911.photobucket.com/albums/a...7pro/photo.jpg http://i911.photobucket.com/albums/a...o/IMG_0214.jpg http://i911.photobucket.com/albums/a...o/IMG_0288.jpg http://i911.photobucket.com/albums/a...o/IMG_0274.jpg http://i911.photobucket.com/albums/a...o/IMG_0290.jpg http://i911.photobucket.com/albums/a...o/IMG_0272.jpg http://i911.photobucket.com/albums/a...o/IMG_0283.jpg Here are some videos... http://static.photobucket.com/player...o/3cedd36b.mp4 http://static.photobucket.com/player...o/df7f397d.mp4 |
this looks like it's going to kick ass when done
|
Thanks! I like feedback. She's running well its just up to my body guy. He's good I just only get his services on sindays and this Sunday is mass so it will be next week... I did all of the ruff in body work he's just finishing it for me. I can't wait had this car for ever... I love her haven driven it on the street since high school... I'm 27 now lol.
http://i911.photobucket.com/albums/a...o/IMG_0241.jpg http://i911.photobucket.com/albums/a...o/IMG_0339.jpg http://i911.photobucket.com/albums/a...o/IMG_0291.jpg http://i911.photobucket.com/albums/a...o/IMG_0292.jpg http://i911.photobucket.com/albums/a...o/IMG_0310.jpg |
please post update and what did you use to make that front end that is awesome:icon_tup:
|
Front end is off an fd, the fd is a bit wider the the fb so with the addition of the wide body it fit perfectly!
I got a t66 so I'll be changing the Turbo out within a week or so I've been remodeling my kitchen for the past month. And I've been workin on my 83 mustang 7. |
what fuel pump are you using
|
Aeromotive a750 with a a1000 filter
|
|
Good? Bad? Not your cup of tea?
|
Dude! Nice job! How'd you mount the LT .. I thought only a 5.0 mustang motor would fit... Since you're apart of the now RX7 "Dark Side" you might want to check out norotors.com. A lot of v8 swap guys over there. A little older crowd. Anyway, I'm here to make 20 posts so I can ask a question here about windshield wipers. Good Luck on your build. Looks fun.
|
Originally Posted by Turbo bondo 7
(Post 10963064)
Good? Bad? Not your cup of tea?
them when well done. However, since you asked... In my opinion - :icon_tdow That bodywork is horrible. :icon_tdow That bodykit is ridiculous, looks fugly as hell :icon_tdow The Turbo is sticking out of the hood :icon_tdow the Turbo is at a weird angle - it's going to smoke all day long :icon_tdow Because the turbo is at a weird angle, the bearings/seals will go bad fast. :icon_tdow The Gauges don't match (I hate that) :icon_tdow Under the hood is sloppy :icon_tdow You should have at least painted the engine bay black with a rattlecan. :icon_tdow The Welds on the Turbo system look like shit and are rusty. :icon_tdow Hate that nasty "Finger Chopper" fan IN FRONT of the Intercooler. |
I can appreciate -
:icon_tup: The Direction you're going with the interior :icon_tup: The Cage looks good. :icon_tup: The complete wiring harness that looks custom. :icon_tup: The FD Seats look good in there. What needs to be done. No matter what, you need Change that front end to an FB/Sa Style one, as that just looks worse that Japanese Bosozoku style ricers. Again, this is just my opinion. It's your car, do what you want. |
Originally Posted by Directfreak
(Post 10966694)
I have nothing against the V8 Swap. In fact, I can appreciate
them when well done. However, since you asked... In my opinion - :icon_tdow That bodywork is horrible. :icon_tdow That bodykit is ridiculous, looks fugly as hell :icon_tdow The Turbo is sticking out of the hood :icon_tdow the Turbo is at a weird angle - it's going to smoke all day long :icon_tdow Because the turbo is at a weird angle, the bearings/seals will go bad fast. :icon_tdow The Gauges don't match (I hate that) :icon_tdow Under the hood is sloppy :icon_tdow You should have at least painted the engine bay black with a rattlecan. :icon_tdow The Welds on the Turbo system look like shit and are rusty. :icon_tdow Hate that nasty "Finger Chopper" fan IN FRONT of the Intercooler. The 'bodykit' is a piece of historyit came off of an emsa series rx7 so I guess if you want to down being able to fit 305 series tires under a first Gen then fine.the front fd nose is because I didn't have the imsa nose and the stock one didn't fit the widebody I think it matches and goes together nicely thankyou. Very observant of you yes my turbo is sticking out of the hood I like it. Nothing like functionality as fresh and heatsoakless as possible. I should have just bought a Turbo kit like I'm sure you did and bolted it on and been another mindless drone with no original ideas. The angle is not too high prolly an optical illusion 5* or so so I shouldn't have any problems and my oil return is at the bottom so no smoking. Oh and now I have a t66 :) Gauges don't match. True story. :-\ That under the hood pic is very old its much cleaner now that's when I was trying to get it to run after sitting for a while. The entire car will be painted once the body work is done and then engine will be takin out. The welds on the manifold are perfect than you I suggest you take a closer look and as far as the rust sorry I can't controle nature. The manifolds will be tempcoated and wrapped. Finger chopper is on the radiator, sorry for trying not to overheat. Opinions are like assholes everybody's got one. Aaron |
Originally Posted by TII_Arekusu
(Post 10966411)
Dude! Nice job! How'd you mount the LT .. I thought only a 5.0 mustang motor would fit... Since you're apart of the now RX7 "Dark Side" you might want to check out norotors.com. A lot of v8 swap guys over there. A little older crowd. Anyway, I'm here to make 20 posts so I can ask a question here about windshield wipers. Good Luck on your build. Looks fun.
I do belong over there at norotors. What's your q on whipers? Aaron |
http://www.anthillz.net/wp-content/u...-Funny-Kid.jpg
Originally Posted by Turbo bondo 7
(Post 10966736)
Opinions are like assholes everybody's got one.
Don't ask for an opinion if you don't want to hear the answer You're going to get all butt-hurt because I told you that FD front end is hideous? I also pointed out other flaws, but whatever - you know best.
Originally Posted by Turbo bondo 7
(Post 10966736)
I should have just bought a Turbo kit like I'm sure you did and bolted it on and been another mindless drone with no original ideas.
Originally Posted by Turbo bondo 7
(Post 10966736)
I do belong over there at norotors
As it is, this thread of yours is in the wrong section to begin with. |
Im interested to see what a coat of paint does for this thing. Its.. interesting. Never been a fan of turbos out of the hood regardless of the performance benefit. What happens if it rains anyways? lol
Either way, I'm sure itll go like hell. |
zoom zoom boom...?....i knew this thread was going to shit quick.....:burn:
|
That "5 degress" elevation on the turbo looks more like 30 or so, to my eye.
I never have understood the idea of asking (repeatedly) for feedback, then trying to get in a pissing match with anyone who gives you one you don't appreciate. I applaud your willingness to be creative. Your snappish attempts to one-up someone who gave you an honest opinion, not so much. |
If you look in the engine bay pic, the pipe itself is on a huge angle. So relative to the floor its prolly a good 30* or so, but i think he means relative to the exhaust pipe its only about 5*.
|
either way the turbo doen't need to be sticking out of the hood as it is. and in my opinion the exhaust needs to be re-configured for better use of it! the car is cool in it's own way and hidiouse in another, but the end result will tell the tail.
ask all the opinions you want too, but keep in mind that it is your project and your car so build it how you want! and remember ask for opinions and you will get them just learn from them..... |
are you running stainless steel lines from the gas tank to the front?
|
Holy shit.
|
DirectFreak, a mindless drone ? Odd thing to say to a guy in the top 10 on the 1/4 mile sheet. There was actually constructive criticism in his posts.
1) The turbo angle is pretty crazy 2) His comment on the engine bay. Sloppiness will come back to bite you in the ass. 3) Not painting the bay. Come on bro our cars are classics meaning they are subject to rust. 4) Bad welds are full of porosity, which causes corrosion and will eventually fail, period. However, I'm still curious to see what it looks like with paint. Building the car isn't a race. The time and attention to detail is what makes the car stand out. The race comes later. |
All I can say is......WOW.....
|
Hey I really like that front end. I always like to see custom cars that are totally different. Looks like it would take in a lot of air too.
Was it a lot of work to fit it? Got any pics looking along the side of the car? How well does the rounded looking front end blend in with the rest of the lines? |
Interesting...
|
WOW... Just looked at this project
Dude, those welds on your cage are not going to pass!! Or shouldn't... That is some poor welding that is going to fail. I bet if I took a hammer to those I could pound them apart, which is a bad weld. I am just speaking from a safety point that if you are depending on this cage you should grind them out and reweld them probably with a tig instead of a mig (and if it was done with a tig SHAME ON YOU!) most cage requirements required their cages to be tig welded anyway. The problem is that there isn't enough heat penetration into the metal. There is lots of porosity which is going to fail. You want a smooth weld with good penetration. That is not a smooth weld... "Standing on soap box: The reason I HATE home made cages is that it is a safety concern. If you did get into a bad wreck an you were going to depend on the cage, the tubes would bust free and probably injure you more then if you were to leave them out. (in specific the one by your head would bust free and probably jab you in the face) IN FACT you are probably safer to leave the cage out then to weld it badly. What good is a cage in a car if it is going to injure you in a wreck. This is coming from the world of Stage Rally Racing where we depend on our cages for safety because we are driving over the speed limit on gravel roads with lots of trees and steep terrain. Most of the time these cars retire because of a bad accident... I am also lecturing you and anyone else who is looking at this and thinking that they can do it. unless you KNOW how to weld on a professional scale, don't weld your cages... http://i911.photobucket.com/albums/a...o/IMG_0241.jpg Just by googling here is an example of what the welds should look like http://allwheelengineering.com/xx/TiWeld.jpg |
wow. didn't know it was possible to rice an fb. whatever floats your boat i guess, but i wouldnt be surprised if this just ends up as scrap.
|
From the pictures I can not tell if I like the body or not. Post some full body shots at differant angles, Thanks.
|
ya wow is all that i can say
|
Well what had happened was...
|
Yes, I am waiting.
|
What a ricer, I nearly vomited when I saw that hideous piece of shit. Haha that turbo is totally gonna starve for oil..thats the most retarded thing ive ever seen. You do know what gravity is right?
|
That is a bit harsh.
|
Yeah, I was under the influence of something affecting my attitute. But as you can tell I really don't like it.
|
Haters..:nono:
|
any updates?
|
Anybody out there?
|
All times are GMT -5. The time now is 06:30 PM. |
© 2024 MH Sub I, LLC dba Internet Brands