95 Chaste White Phoenix
#76
The other day as I was heading to a buddy’s house, a rock, a wrench, a bullet (what ever it was sounded like my wheel fell off) introduced itself to my new passenger side Setrab Oil cooler. So I ordered a new one and it’s arriving today.
It doesn’t leak and I could’ve just sent it for DGRR or just turn it around to a fresh back side. But when it’s a replaceable part for 185.00 shipped, it’s a no brained to just replace it like a worn part.
It doesn’t leak and I could’ve just sent it for DGRR or just turn it around to a fresh back side. But when it’s a replaceable part for 185.00 shipped, it’s a no brained to just replace it like a worn part.
#77
Ban Peak
iTrader: (49)
The radio looks good, the surround trim doesn't look like the match is that bad for the '94+ texture as well. Any pics of it from farther away?
I can't believe that oil cooler didn't leak, it looks like the hit was hard! I'm glad to see if held up and didn't cause any issues for you other than the inconvenience of replacing it.
I can't believe that oil cooler didn't leak, it looks like the hit was hard! I'm glad to see if held up and didn't cause any issues for you other than the inconvenience of replacing it.
The following users liked this post:
Rocketeerbandit (04-25-19)
The following users liked this post:
Rocketeerbandit (04-25-19)
#84
Professional Tinkerer
#85
by Gerald Mugar, on Flickr
by Gerald Mugar, on Flickr
by Gerald Mugar, on Flickr
by Gerald Mugar, on Flickr
by Gerald Mugar, on Flickr
Last edited by Rocketeerbandit; 04-29-19 at 09:50 PM.
The following users liked this post:
ZE Power MX6 (04-30-19)
The following users liked this post:
Rocketeerbandit (04-30-19)
The following users liked this post:
Rocketeerbandit (04-30-19)
The following users liked this post:
Rocketeerbandit (04-30-19)
#89
The oil cooler vents are straight forward and easy. Getting the mouth of the bumper for the radiator was difficult on the sole fact that the top of the inside bumper mounts are further out while the bottom are further in. Which I had to take off and form the mesh diagonally so it looks straight as possible rather then it concaving in.
#90
Boilermakers!
iTrader: (157)
Yeah, I remember that about the bumper mouth. I mounted an aluminum rod on the rebar using the stock foglight mounting holes, the top of the mesh is ziptied to the rod and the bottom of the mesh mount just like yours. The rod seats a little further back on the rebar than the edge of those funky bumper skin edges, so I'm able to re-install those 3 plastic inserts that attach the skin to the rebar.
The following users liked this post:
Rocketeerbandit (05-04-19)
The following users liked this post:
Rocketeerbandit (05-04-19)
The following users liked this post:
Rocketeerbandit (05-04-19)
#93
My eyes are getting worse with age, and the play of light and shadows and distance messes with my ability the environment around me. These should help out a bit when I’m driving in the rx7.
Bi-Led headlights
I’ve got so used to the 17 Mazda CX-5 and the 19 Chevy Silverado LED lights that any output less then has me squinting a bit and driving slower.
Bi-Led headlights
I’ve got so used to the 17 Mazda CX-5 and the 19 Chevy Silverado LED lights that any output less then has me squinting a bit and driving slower.
Last edited by Rocketeerbandit; 03-20-20 at 01:22 PM.
#94
RX-7 Bad Ass
iTrader: (55)
Sakebomb Garage kit? I LOVE mine.
Dale
Dale
#95
close, but they are AZ’s small batch production bi led lights. He did such an amazing job in the quality of the product. It’s sad to see that everyone can not benefit from his product. I feel lucky and a bit proud that I was able to get a set at the right moment.
The following users liked this post:
Rocketeerbandit (04-24-20)
The following users liked this post:
Rocketeerbandit (04-24-20)
The following users liked this post:
Rocketeerbandit (04-24-20)