94 Build... GT35R, RE Vmount and a whole lot more............ NOW WITH PISTONS!!
#1
94 Build... GT35R, RE Vmount and a whole lot more............ NOW WITH PISTONS!!
The time has finally come to post my build thread as it comes to a relative end. I have been holding off as I wanted to post my dyno'd numbers at the same time. I pulled the engine and transmission in June to start a single turbo project. I had completely finished the chassis preparation a few months before.
With the chassis prepped & ready to rock, it was time to start buying parts & disassembling everything for the big swap. Below is partial list of everything that went into it. I'll label the pictures with what parts were used & what was done. It's been one hell of a project, but I am nothing short of ecstatic with the results. The car is an absolute blast with room to grow.
Vendors
Rotary Extreme - Ben from RE provided such an amazing service. Helpful, tentative, and an overall joy to work with. His Vmount kit is absolutely beautiful and it was a real joy doing business with such a caring vendor. If you are considering his kit or any part he sells, buy with confidence people. The guy is just awesome to work with.
SpeedOne - Dave tuned my car and did a GREAT job doing it. I can not say enough good things about him, his shop, and his service. He literally talked me through setting my car up over the phone enough to safely drive it to him for the tune. He took his time, did it right, and was very professional. I plan to take it back to him when the meth kit goes on. I have nothing but GREAT things to say about the entire experience!
The day before I pulled it...
Pulling the engine & transmission.....
Stripping everything down....
Single turbo wiring harness conversion...
Battery Relocation & gauge install....
With the chassis prepped & ready to rock, it was time to start buying parts & disassembling everything for the big swap. Below is partial list of everything that went into it. I'll label the pictures with what parts were used & what was done. It's been one hell of a project, but I am nothing short of ecstatic with the results. The car is an absolute blast with room to grow.
Vendors
Rotary Extreme - Ben from RE provided such an amazing service. Helpful, tentative, and an overall joy to work with. His Vmount kit is absolutely beautiful and it was a real joy doing business with such a caring vendor. If you are considering his kit or any part he sells, buy with confidence people. The guy is just awesome to work with.
SpeedOne - Dave tuned my car and did a GREAT job doing it. I can not say enough good things about him, his shop, and his service. He literally talked me through setting my car up over the phone enough to safely drive it to him for the tune. He took his time, did it right, and was very professional. I plan to take it back to him when the meth kit goes on. I have nothing but GREAT things to say about the entire experience!
The day before I pulled it...
Pulling the engine & transmission.....
Stripping everything down....
Single turbo wiring harness conversion...
Battery Relocation & gauge install....
Last edited by GoodfellaFD3S; 11-24-12 at 09:01 PM.
#2
Fuel pump rewire....
Supra pump install & removing the Walbro....
Cleaning engine bay and painting lower rails....
Fuel System Parts.... - 850 pri, 1680 sec, Aeromotive FPR, AN fittings & braided lines...
Block cleaned & fuel system fitted. Manifolds were ceramichromed by IR Performance. I was very pleased with the results.....
Engine & rebuilt transmission back in the car. Turbo test fitted....
More test fitting with manifold & turbo elbow welding.
Supra pump install & removing the Walbro....
Cleaning engine bay and painting lower rails....
Fuel System Parts.... - 850 pri, 1680 sec, Aeromotive FPR, AN fittings & braided lines...
Block cleaned & fuel system fitted. Manifolds were ceramichromed by IR Performance. I was very pleased with the results.....
Engine & rebuilt transmission back in the car. Turbo test fitted....
More test fitting with manifold & turbo elbow welding.
Last edited by GoodfellaFD3S; 11-24-12 at 09:02 PM.
#3
Rotary Extreme Track Vmount kit, pulley kit, & hood dampeners....
Vmount Installation....
R1 dual oil coolers with AN fittings & stainless lines. PM me for a complete part list....
ASSEMBLED & COMPLETE!!
Vmount Installation....
R1 dual oil coolers with AN fittings & stainless lines. PM me for a complete part list....
ASSEMBLED & COMPLETE!!
Last edited by GoodfellaFD3S; 11-24-12 at 09:03 PM.
#5
386whp & 331ftq at 15psi
Dyno Video
http://www.youtube.com/watch?v=t0fqKel946Y
Final Thoughts....
I couldn't be happier with the results. My power levels for a stock port engine are quite good. The car is VERY quick but controllable. It lights up my 285's 1st through 3rd, but the spool is so fast & smooth that it's very drivable. I do plan to run 50/50 meth with a retune. I'm not shooting for the stars but would like a nice cushion with pump gas.
I am now focusing on having the car repainted, & finishing some aesthetics that are long overdue.
Dyno Video
http://www.youtube.com/watch?v=t0fqKel946Y
Final Thoughts....
I couldn't be happier with the results. My power levels for a stock port engine are quite good. The car is VERY quick but controllable. It lights up my 285's 1st through 3rd, but the spool is so fast & smooth that it's very drivable. I do plan to run 50/50 meth with a retune. I'm not shooting for the stars but would like a nice cushion with pump gas.
I am now focusing on having the car repainted, & finishing some aesthetics that are long overdue.
Trending Topics
#8
Banned. I got OWNED!!!
Join Date: Mar 2009
Location: NC
Posts: 1,045
Likes: 0
Received 0 Likes
on
0 Posts
Amazing project, it must be very satisfying to essentially do it all yourself and see the results with each step. Are you doing the bushings as well or is that done?
#12
www.powerflexusa.com
Dave did do a pull with the filter removed as we discussed it's possible limiting factor. It made absolutely NO change. Honestly, we were both a bit surprised, but I definitely wasn't going to complain. We both did agree however that when I start to turn up the boost later, it could become a hinderence.
As far as a screen goes, never on a street car. I have looked at other options when the time comes, but that will be awhile.
I am using a PFC for EMS.
Thank you all for the kind words. I've been waiting to make this thread for quite some time. It's always great to share my work & thoughts with this awesome community.
-XLR8
#18
Garage Hero
iTrader: (93)
Hell yea!!! So i ended up going with the Super-pro kit because I really wasn't to confident in the reliability of the other bushings... although nice.. I didn't want to wait and feel like i might get cheated or anything. The horror stories on the group buys was the culprit haha.
#19
Hell yea!!! So i ended up going with the Super-pro kit because I really wasn't to confident in the reliability of the other bushings... although nice.. I didn't want to wait and feel like i might get cheated or anything. The horror stories on the group buys was the culprit haha.