modification list with pictures - lots off stuff
well, i torn the entire top off again this winter to redoe the silicone hose job in hopes that it would fix my sloppy transition problem, while I was at I also did:
went from purple to yellow silicone hose http://www.myrx7.com/images/pages/DSC00331.html http://www.myrx7.com/images/pages/DSC00498.html http://www.myrx7.com/images/pages/hose_comp.html added the hyper ground system http://www.myrx7.com/images/pages/DSC00284.html http://www.myrx7.com/images/pages/DSC00337.html http://www.myrx7.com/images/pages/DSC00378.html http://www.myrx7.com/images/pages/DSC00451.html http://www.myrx7.com/images/pages/DSC00494.html http://www.myrx7.com/images/pages/DSC00496.html http://www.myrx7.com/images/pages/DSC00497.html http://www.myrx7.com/images/pages/hgs_vs_stock_uim.html added the s2000 start button (info from http://iluvmyrx7.com and help from jim labreck, thanks guys) http://www.myrx7.com/images/pages/DSC00384.html http://www.myrx7.com/images/pages/DSC00389.html polished the intake manifold and throttle body (thanks to twinturboteddy on the rx7 forum) http://www.myrx7.com/images/pages/DSC00471.html http://www.myrx7.com/images/pages/DSC00479.html polished alternator shell (thanks to twinturboteddy on the rx7 forum) http://www.myrx7.com/images/pages/DSC00470.html polished metal intake pipes (thanks to twinturboteddy on the rx7 forum) http://www.myrx7.com/images/pages/DSC00481.html removed the double throttle control system (sorry, forgot to take a pic, i used a bold to plug the butterfly shaft hole.) removed the automatic warm up system (AWS) http://www.myrx7.com/images/pages/DSC00484.html had my tail lights modified to the j-spec type circles, but silver instead of black (thanks to ryan wolf) http://www.myrx7.com/images/pages/DSC00453.html installed widefoot aluminum gas pedal and deadpedal and passsenger foot rest (thanks to sled driver of the rx7 forum) http://www.myrx7.com/images/pages/DSC00275.html http://www.myrx7.com/images/pages/DSC00277.html http://www.myrx7.com/images/pages/DSC00281.html replaced the solenoid rack crappy 'strip happy' screws with hardened allen head bolts http://www.myrx7.com/images/pages/DSC00316.html http://www.myrx7.com/images/pages/DSC00334.html replaced the stock check valves with heavy duty viton seal check valves http://www.myrx7.com/images/pages/DSC00293.html http://www.myrx7.com/images/pages/DSC00332.html replaced some turbo oil return gaskets (was leaking a bit) (good advice from jeff) http://www.myrx7.com/images/pages/leak-detection.html http://www.myrx7.com/images/pages/DSC00448.html new downpipe and cat and catback gaskets http://www.myrx7.com/images/pages/DSC00440.html unorthodox pully set, waterpump, alternator, powersteering (have not installed the main pully yet) http://www.myrx7.com/images/pages/DSC00498.html new 02 sensor http://www.myrx7.com/images/pages/DSC00398.html http://www.myrx7.com/images/pages/DSC00444.html new stant 16psi radiator cap (will become obsoleet soon, moving to evans coolant) http://www.myrx7.com/images/pages/DSC00367.html made a bracket for the temp gage mod black box, now its nice and secure http://www.myrx7.com/images/pages/DSC00370.html http://www.myrx7.com/images/pages/DSC00375.html http://www.myrx7.com/images/pages/DSC00372.html http://www.myrx7.com/images/pages/DSC00374.html widefoot swaybar mounts (thanks to David Breslau) http://www.myrx7.com/images/pages/DSC00487.html http://www.myrx7.com/images/pages/DSC00490.html http://www.myrx7.com/images/pages/DSC00493.html changed boost control to manual bleed valves and eliminated the ecu/solenoids from the loop (thanks to Kahren) http://www.myrx7.com/images/pages/DSC00422.html http://www.myrx7.com/images/pages/DSC00421.html removed the stock air box and went with 2 k&n tube filters http://www.myrx7.com/images/pages/DSC00339.html http://www.myrx7.com/images/pages/DSC00498.html fabricated a heat sheild for the K&N airfilters (still finishing it up) http://www.myrx7.com/images/pages/DSC00514.html http://www.myrx7.com/images/pages/DSC00515.html http://www.myrx7.com/images/pages/DSC00513.html modified the open oil cooler to be a fresh air ram to the K&n filters http://www.myrx7.com/images/pages/DSC00500.html http://www.myrx7.com/images/pages/DSC00503.html http://www.myrx7.com/images/pages/DSC00506.html I just got it all back together so i have only test drove it a few times, with boost controllers totoally closed, but the transition was very quick, a solid 7-6-7 pattern, but its too early to make conclusions yet, I still need to tweak the boost up to 10 and see how well i can get the transition. Im still with the stock ecu, so i'll be keeping boost at around 9.5~10 since im running dp, catback, and intake. I love the fact that it does not rev up to 3K at a cold start anymore, and it seems to idle just fine with the aws and double throttle removed (i was worried about the stories of sporatice idle after these mods), in fact it purrs like a kitten, maybe better than before because of the new HGS grounds. There is only once thing I have to 'debug' and that is after idling a while the ACV will switch and relief air out to atmosphere, when it does this (infamous moo sound) the idle goes to hell (hunts around realy heavily), however if I put my hand in front of the air tube and block the air coming out, it goes back to normal, or if it ACV switches back (not relieving the air out) it goes back to normal, so I still have to figure that one out. No real power mods so no HP gains, the intake might add some but im dialing down the boost so its a wash. I am going to focus on adjusting my camber and seeing how it handles before i try to push up power. I am not a good enough driver to take on more power ...yet (heheheh...MUAHAHAHHAHAH!!!!). When i am ready for a power push, the power FC and ASP medium intercooler (and then moving to 12lbs boost)...is not far behind. I can't wait till the racin season starts :-) |
Wow!! :eek:
That's awesome, thanks for all the pictures. |
wow thats alot of work looks great i love the ram air idea... was that a lot of work?
|
Dude, whats your secret for polishing? It looks beautiful.
|
Originally posted by 97GST Wow!! :eek: That's awesome, thanks for all the pictures. |
Originally posted by af908 wow thats alot of work looks great i love the ram air idea... was that a lot of work? |
Originally posted by Pherrus1 Dude, whats your secret for polishing? It looks beautiful. |
NIce man! Good thread!
|
Yes his secret sauce is the one and only TTT ;) and a little creativity :).
|
Originally posted by vudoodoodoo NIce man! Good thread! |
Originally posted by Silex Yes his secret sauce is the one and only TTT ;) and a little creativity :). |
thanks for sharing !
|
Originally posted by apneablue thanks for sharing ! by the way, i like ur Defi Link System Boost...are you happy with it? accuracy, et... |
Wow thats really nice. I hope to do some of that stuff like that sometimes soon. How much did that polish job run you. I was thinking of doing it myself but don't think it would turn out as good as I want it to. Keep it up.
|
ask TTT , he can give you a polishing quote based on what you want done
|
Where did you route the ram air, i cant seem to find a good hole. And where did you buy you check valves? Looks Good man!
|
Originally posted by Pherrus1 Where did you route the ram air, i cant seem to find a good hole. And where did you buy you check valves? Looks Good man! the ram air tube i routed by making a hard right angle then bending it up into the spot where the foam seal used to be (i removed the foam)...i can post a pic if you want |
That'd be sweet
|
nice work, and thanks for all the pics.
keep us posted or PM me on the Hyper Ground system results. I have the dreaded 3K hesitation, and I'm thinking of trying to upgrade all the ground wires. |
very nice job on your fd,turned out great,question for you what is the part# for those k&n intake filters or what size are they thanks damian.
|
nice, you'll have fun with that set-up.
|
Originally posted by damian ask TTT , he can give you a polishing quote based on what you want done |
ahh teddy, well thanks for gettin me in on the last few runs!!! :-)
|
just wanted to add to my list....here is a cover I fabricated for the hole that shows up in the stock intercooler duct when you remove the stock airbox and front plastic thing that connects them. I used some sheetmetal and a rivits
http://www.myrx7.com/images/stock_intercooler_cover.jpg |
Originally posted by jg937 very nice job on your fd,turned out great,question for you what is the part# for those k&n intake filters or what size are they thanks damian. these are the summitracing part numbers: part number on the K&N filters is: KNN-RD-0720 part number for small airpump k&n filter: KNN-62-1370 |
All times are GMT -5. The time now is 02:48 PM. |
© 2024 MH Sub I, LLC dba Internet Brands