I got an ebay one on my car as well. It collects the same crude like shown on gracer7-rx7 pictures. The plating on my plug is flaking ._. I think it started to flake because everytime I remove the plug I expect it to drop, but it goes clunk on the pan.

damn it, I saw SARD had some for $5 but they're all out of stock. our size too, m14x1.5
http://www.more-japan.com/halloween-sale-sard/

All hondas have same size plug so shouldn't be too hard to find. I think plug magnet would be a lot better than filter magnet as the filter is under pressure.

And the oil pan isn't?

Just FYI in case you guys didn't notice it...

The Honda and other oil drain plugs probably won't work b/c they are too long. The FD plug is short and hits a stoppage if you try and screw in something too long. That is why Richard at Drain Plug Magnets and I worked on creating a FD/RX7 specific application that was shorter:
http://www.drainplugmagnets.com/mazda.php

No the oil pan is not under pressure. If the drain plug gasket is bad it drips oil.. If the filter gasket is bad it sprays everywhere.

No Honda plugs are not longer. Honda plugs made for aluminum pans are yes but most are short thread. I have a Honda plug in now.

Oil filters that have a built in magnet? SARD OIL FILTERS

I would vote for the drain pan plug. Reason being that ferrous particles are heavier and they slosh around in the bottom of the oil pan without all getting sucked up to the filter. Being heavy, they don't even drain out during oil changes, so a magnet is the only sure way to collect them.

Gracer, please note the results of your next oil change. I have a hunch you collected particles that were there for a long time and you will find a lot less particles on subsequent oil changes. We find that happens when we sell a brand new gear reducer since it's very hard to build things perfectly clean and the first few hours of loaded operation tend to liberate most of the particles right away.

The next time I buy stuff from Digikey or McMaster, I'll have to pick up a small magnet and JB weld it on the end of my stock plug. (Edit: McMaster 5857K11 might fit). That should work just as well for a couple of dollars.

David

Willl do David. Did you notice my oil analysis?
https://www.rx7club.com/showpost.php...6&postcount=94

our transmissions should have them stock.... mine did

i recently changed my tranny and diff oil to Amsoil 80/90 and Amsoil Gear lube respectively.

i checked the drain plugs and they are indeed magnetic..... mine had what looked like sludge buildup in it. I called a transmission shop and they said this "sludge" is normal for cars this age because its the normal wear of the bearings, gears etc etc that the magnet captures and overtime this will buildup and look like grey sludge.
they said as long as i clean out the plugs the magnet should be fine.

The manual transmissions have a donut magnet bolted to the floor pan. You can clean this by removing the rectangular pan during an oil change.

Gracer, I'm not an engine oil analysis expert but my personal experience is that if you don't mind the cost of the tests, it's worth getting a VOA and running a test for more than one oil change. Comparing to absolute "alarm" or "normal" numbers is much less insightful than tracking trends in your particular application.

David

My experience confirms your hunch: I did a second oil change over 3500 miles interval. Did not find alot of particles as during the first time.

Just did another oil change. The magnetic drain plug did not accumulate nearly as much material as it did in the first oil change.

I am also sending another sample of my oil to Blackstone for analysis. Will post results in the used oil analysis thread.

Dimple has two Mazda plugs listed in their website and they both seem low profile, one of them being the newer one. Which one is for the RX7?

http://www.drainplugmagnets.com/mazda.php

Also I don't know why the new one is more expensive :scratch:

I am guessing one is more expensive because of the o-ring and not needing metal gaskets/seal.

I have the short cheaper one on my FD.

I asked the same question to Richard the owner of Drainplugmagnets.com and this is his reply:

"Since you have seen the web site there has been a change in our whole line. We have a new line of washer type plugs and they are available now, only not on the web site just yet till this week end.
They are $29.95 and are fantastic!. Order the SS M14X1.5 and you will receive the New washer type M14X1.5, SHORT . Which is for your vehicle. Made in USA."

He sounds quite passionate about his plugs :D I just ordered one anyway.

i bought the competition oil pan for my 12A and it came with a magnetic plug too. first couple of oil changes from a new engine build, i reused tension bolts everything else was NEW, had it come out with "stuff" on it. last oil change, it was pretty clean.

i don't think you need one, but it is nice to have.