Jacks, Ramps, Jack Stands?
 

The R1 lip makes it a little tougher to get the car up in the air at home. I need some recommendations on Jacks or ramps that work well on an FD. I really don't like using the side rails to lift the car, already have at least one indent from that. My floor jack isn't long enough to reach the crossmember from the front, so that doesn't cut it.

Once in the air, I'd rather use two jack stands in the front, but again not along the side rails. I imagine the crossmember would be the only good option to the sides, right?

Any recommendations?

Jack it up with the stock jack on the side rail which doesn't leave a mark and then jack it in the front.

i use the stock one jack and if i need it to go higher i put a brick under the jack... once in the air i use the horse i believe its called (stands) under the car not on the side rails

I use a hockey puck with a groove notched into it that fits over the lip that the stock jack uses. I place the puck on a regular jack, position the jack and jack it up. Works great.

I drive it up 2 small red bricks and then most floor jacks will fit under. I place the jack stands at the cross member also.

Ramps don't work. I have a pair of the low profile Rhino ramps sitting in the garage gathering dust...

get 4 2x6x8 pieces of wood and drive up on them, then place the other two and pull up alittle more.

thats how i change my oil and get under my car.

Heh, I do almost the same thing. Drive up on some 2x6 boards, then use a racing jack to jack it up, then put it on stands.

I used to use homemade ramps of 2 stacked 2x10s, but now I just use my AC Hydraulics jack (http://www.ultimategarage.com/shop/p...roducts_id=863) and it can reach the front crossmember with the R1 lip, 1" drop, and no ramps. It helps to manually lift the front a few inches before sliding the jack under. I also put a mark on the jack that lines up with the front of the lip when the saddle is under the crossmember.

If the car was lowered any more I'd probably need to AC jack and a ramp to get the front started.

Dave

Ramps
 

I use the extended ramps from Griot's Garage (griotsgarage.com). The intial ramp angle is pretty small so they don't slip forward as you drive up them. Each ramp also packs up into 2 pieces so they store in around the same space as regular ramps. Re-assembly is very quick and easy, (no fasteners). Approx. $65 a pair, incluing shipping last time I looked. WELL worth the money.

Do the Griot's ramps work with the R1 lip?

Ramps
 

Sorry, I don't know. Mine's a '93 touring, and has plenty of clearance due to the small initial angle of the ramps. I'm not sufficiently familiar with the R1 lip to know whether there is enough clearance for it. Suffice to say, these ramps have the most clearance of any I have found.

Maybe you could post asking if there is anyone near to your location who has a set, then you could try 'em!

Good luck

^Can I try yours? :)

Better yet, can you post a pic of the ramp in front of the car as the tire meets the beginning of the ramp? I suspect that the R1 and 99 lip would interfere due to lack of ground clearance anyway.

Ramps
 

You're welcome to try mine, but, checking on your location, it's a bit far for you to go, (I'm in Laguna Hills, Orange County). Anyway, I'll take a pic. for you sometime over the weekend and post it.

Dave

Went to Lowes, they gave me several blocks of wood that I put under my regular car jack and the extra inches did the trick. Now I'm able to put my jack stands (at higher settings) under the lips and the whole thing is steady.

thanks for the help.

Great!

Dave

Anyone tried the NAPA low profile jack?

http://www.napaonline.com/MasterPage...ion=Floor+Jack

Unless you are jacking at the pinch seam, none of the low profile jacks will be able to get far enough under the car to reach an appropriate jacking location. Sadly you really do need one of those low and long or extended jacks to really be useful.

I have the Sears low profile aluminum racing jack. Its low enough but as you slide it under, the body of the jack gets higher and doesn't get far enough past the pinch seam to reach a good jacking location.

Maybe your car is lowered? I can reach just about anywhere worthwhile with my low profile jack. Any more though I just jack at the pinch seam. You can buy a replacement cup for the jack that is just a big rubber pad, thats what I use and never have problems with it damaging the pinch.