aftermarket SMIC lets see em
 

thinking of going back to an aftermarket stock mount IC. most likely pettit CCIII, only thing holding me back is price. please share your setups to see if I can make my own setup for less $$$.

Thanks,
Lazaro

If you can make an AST/M2 Medium intercooler, I'll buy it. I am also looking for a SMIC that doesn't require me to relocate my battery.

^ You mean like this? Goes really well with the TurboJeff Battery Tray too :D

Attachment 722278

^ please let me see the duct. is it pettit ? anyone knows if this duct fit Greddy SMIC ?

Here is an older picture showing the duct. I do believe it is VERY similar to the Petit Duct. THe pictures I have seen look as if they are the exact same as the M2 duct.

Attachment 722279

thanks. I think pettit is a bit bigger and require batter relocation. unless someone please confirm it is not.

wow I like your setup., seriously I regret getting greddy smic because I still have very poor ducting (stock)

probably going to end up fabing up one of my own. anyone got pics of the pettit CIII intercooler found the ic he uses (thanks moosejaw) just need to know how they bolt up. anyone care to post pics of theirs I would be very thankful.

Pfs smic
 

Heres my Peter farrel supercars SMIC with custom duct. Perfect fit in stock location and is 255% larger core volume than stock.

old school pettit

i know i've posted this like 20 times on this forum...

but here's my home-made SMIC. the IC is the same size as the pettit cool charge iii kit, but my entire setup cost about 1/3 of the price.

http://carphotos.cardomain.com/ride_...0277_large.jpg

i actually used a pettit cool charge iii duct. since my IC core was the same size. i modified the pettit duct to be a little longer, and also added a 12" switched e-fan, and heat shielding to the end tanks:

stock vs new
http://memimage.cardomain.com/member...9_200_full.jpg

modified the efini y-pipe to make it shorter, add a splitter, and rotate the flange 90degrees:
http://memimage.cardomain.com/ride_i...0243_large.jpg

made a pipe to connect the y-pipe to the IC:
http://memimage.cardomain.com/ride_i...0248_large.jpg

added a 12" e-fan (used my fog light switch since i don't have fogs) and heat shielding:
http://memimage.cardomain.com/ride_i...0281_large.jpg

extended duct:
http://memimage.cardomain.com/ride_i...0285_large.jpg

this setup has worked well but now i really want to build a v-mount :D

The Blitz SMIC in my car fits with the stock battery, airbox, IC duct...even the intake crossover duct is retained for that OEM, smoggable look. ;)

http://www.msprotege.com/members/Natey/RX-7/FOS_3.jpg
http://www.msprotege.com/members/Nat...z/P3220112.JPG

^^that blitz doesnt look like it would be any better then the stocker.
heres my pettit with a single turbo set up.

Look closer. ;)

Also, my car just passed California Smog inspection last week, something that would never happen with a single turbo, loud BOV, and blatantly oversized IC.

Blitz and Greddy don't make the smic anymore, correct?

The old school Pettit CCII and most of the other larger SMIC's do not bolt up to anything. They are held in place by the the force pushing against the duct and the hose clamps. Only the SMIC's which bolt up to the stock duct like the Greddy and Blitz actually bolt to something other than the IC hoses.

Pettit has two IC's which they sell:

Cool Charge II & III - II does not require battery relocation and III does. This is the same for the M2/ASP IC's in which the Medium does not require battery relocation (may require a smaller battery) where as the Large does require battery relocation.


That is correct. You'll have to find both of them used (and they usually go pretty quick).

can someone measure their pettit duct and ic for me or anyone know the sizes. cause I see to ic I can get but one is 24" in length and the other is 21.5 in length need to know which one will fit better on the duct.

Thanks Mahjk. I'll check with them again on the duct.

I know I know, probably splitting hairs....but actually the PFS SMIC sits on the crossmember just like stock but is also fastened to the duct via two brackets on either side with M6 bolts. The duct is also one of the more sturdy I've seen. It's made out of gel-coated FG and is pretty stable by itself.
:)

Not for long, buuuuut
Attachment 722280

the CCIII duct fits a 17" or 18" wide, 12" tall CORE.

This is my RE Amemiya SMIC:
http://sphotos.ak.fbcdn.net/hphotos-..._7194391_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-..._1831481_n.jpg

Installed photos with stock air box and stock battery:
http://sphotos.ak.fbcdn.net/hphotos-..._3902090_n.jpg

http://sphotos.ak.fbcdn.net/hphotos-..._4167238_n.jpg

here's mine:

https://www.rx7club.com/picture.php?...ictureid=27374


Prices from memory:

Goodspeed SMIC (same size as pettit CCIII) ~ $200
Pettit duct ~ $200
Pettit cold side pipe ~ $125
Custom made hotside pipe ~ $100

Total: $625

SWEEEEEEEEEET re-amemiya SMIC you got Chris :)

:scratch: When I mix and match, it never seems to turn out half that nice. :icon_tup: