*vid* my car running
 

finally got a camera, link on other thread but not everyone follows it-


http://www.vosko.net/media/rotary/GothamBridgeport.wmv

That SUCKED!!!! Where's the video of the 7 running against the 9?????
Just kidding, sounding funky, looking good.

thought the vid was great, really wanted u to rev the FD up though like what was done with the 911

will have more entertaining videos when the motor is properly seaonsed, as for now, i'm babying it

Great vid man. You can hear your 7 at idle better than you can hear the porsche revving:) Great Stuff. Did you just send your housings and stuff to gotham to get them to port it, because I am planning on doing the same thing in the next few months. If so, how much did just the porting cost if you don't mind telling.

It sounds great and will be awaiting more vids after break-in. I need a damn dig. camera, hate the stupid VHS-C stuff.

nice car man! id like to see it someday. glad to hear that its finally running, after all the trouble you have been through...

That is one loud exhaust :)

wot must instill fear

the greddy SP is one of the quietest that i have used...

talk to steve kan about pricing

the bridge isn't for a street car...IMO...lots and lots and lots of tuning, takes me about 3 mins to crank it when it's really cold....but so worth it IMO

I like it, still would like to see the vids of it 100% ready to run

pretty nice vid

man that server is fast :D

Shit yeah!!!

93BlackFD: Is it a full bridgeport or just a half-bridge? I am desiding between large street port and half bridge port.

your idle is a bit fast

it's a half bridge...

do some thought on it, there are things about the half bridge that you will need to think about....engine braking, gas mileage, emissions (if applicable), engine management/tuning, driveability, etc

it's not for the weak...i'd hate to see you get one and then curse at it down the road :)

haha thanks alot. right now my car is a daily driver, but is progressively being built towards a track car (actually is there, just don't have a daily driver car yet) My motor right now has super low compression (about 70psi, but still runs strong) and I am going to buy a core and rebuild/port it and am deciding which one to go with and from where.

I understand the other stuff you were talking about but didn't really understand what you meant by "engine braking". I know what engine braking is, but not how porting affects it.

Thanks
M-P

your car will want to hop and jolt when you try to coast in a gear....also known as engine braking

not sure if steve can tune around that, just make sure you know what you're getting into

i am thinking of doing a large street port motor and having two motors essentially, because i like to drive my car around without hassle of having to worry how long it will take to crank, etc etc

i think most of your problems are tuning

i've seen full race full bridge motors start with a carb after two cranks...

So wait wait, you have a 996 Turbo, and a 1/2 bridge FD? I wanna be you!

ok so when it is heavily ported it will want to buck more than it does now? Not a real big deal to me, but I am just thinking a real big street port might be better for me anyway. From what I have read at least. I will call steve whenever I get my core motor taken apart.

not sure if it's in the tuning or the motor....like vosko said

steve is going to check the car out when he comes to alabama in march

cool vid.

Bridgeport sounds badass
definetly film a race with the Porsche sometime

u and ruiner.. and you didnt invite me! shame on you!

a street port is not for everyone and a bridge port is way out there.

Some times i regret my street port.........

partly why it's prolly tak'n him 3 min to start is the low compression.

used housing always take a bit longer to build compression.

but it shouldn't be too hard to start.