What would you folks like to see fabricated for the FC??? (seriously)
Thread Starter
Banned. I got OWNED!!!
Joined: Aug 2004
Posts: 8,789
Likes: 2
From: Jacksonville, NC
Yes we are planning to make the TID roughly based off the Banzai design, so you can retain the use of the S4 AFM... 
Sorry the bar will not have an engine brace built in...
DerangedHermit I do want to try the aero brackets, but I'm not sure what sort of time issues we'll face, since we are gonna be pretty busy with the workload we have already seemed to scare up...
Sorry the bar will not have an engine brace built in...
DerangedHermit I do want to try the aero brackets, but I'm not sure what sort of time issues we'll face, since we are gonna be pretty busy with the workload we have already seemed to scare up...
Rotary Enthusiast
Joined: Apr 2005
Posts: 935
Likes: 1
From: PA
I don't know if this was suggested but check this out: http://www.ioportracing.com/Merchant...oduct_Code=GB3
I ordered one of these but the problem is that it has to be modified at the ends to fit the rx7 angles.
I ordered one of these but the problem is that it has to be modified at the ends to fit the rx7 angles.
Joined: May 2006
Posts: 441
Likes: 0
From: Marshfield, Massachusetts
Originally Posted by gingenhagen
here's a hint...fc owners are the cheapest of all. I mean, just look at me. Just off the top of my head, prices I'd be willing to pay for things that I want.
Cold air box for $20.
TID for $20.
FMIC & piping for $500.
front strut bar for $30.
Cold air box for $20.
TID for $20.
FMIC & piping for $500.
front strut bar for $30.
HAHAHAHAHA... You've obviously never talked to a first gen MR2 owner. Few real sports car owners (front-drivers excluded) are cheaper than AW11 MR2 owners, trust me.
Thread Starter
Banned. I got OWNED!!!
Joined: Aug 2004
Posts: 8,789
Likes: 2
From: Jacksonville, NC
Hey everyone sorry for the unexpected delays... We've both had alot on our plates lately, so we had to shift focus temporarily... This is still a big priority though, and perhaps this week we can get a batch of the bars made up... We have everything sitting there ready to knock them out, but just haven't had the time or energy lately... Thanks for all your patience!
Senior Member
Joined: Jan 2004
Posts: 515
Likes: 0
From: Utah (land of mountains)
Originally Posted by 13b4me
Already being made by someone... Harness bar is in the works...
Is it going to be a bolt in? I know some ppl have one that bolts across the stock shoulder strap locations, and still retains the stock belts (required for some auto-x classes)...
Seriously interested in that though, I have the harness sitting here waiting to be installed... lol
Originally Posted by 13b4me
DerangedHermit I do want to try the aero brackets, but I'm not sure what sort of time issues we'll face, since we are gonna be pretty busy with the workload we have already seemed to scare up...
Damn you people, I miss my rubber pieces
and need to get them back so chime in if you're also interested. More people = more motivation.
Originally Posted by Goofy
Can I get a picture of the piece you're talking about?
If so, here's my original post. Let me try to find the pictures I took too.
Originally Posted by DerangedHermit
How about the front metal brackets that attach to the rubber aero kit pieces.
As seen from the black piece under the front left turn signal. The bracket that attaches those thingies to the car...
As seen from the black piece under the front left turn signal. The bracket that attaches those thingies to the car...
Last edited by My5ABaby; May 16, 2006 at 12:44 PM.
Originally Posted by 13b4me
Those don't look too difficult... I can almost bet you could get them through Mazda though... Have you checked the parts fiche?
. I was bored so I even checked on the rubber pieces that they connect and Mazda wants $387.50 *per* side...
RotoriousRx7
Joined: Oct 2005
Posts: 1,236
Likes: 0
From: goodlettsville,tennessee 37072
well on the throttle body questions why not take a factory tb and gut it out of all the butterflies and port the **** out of it and make a single butterfly throttlebody like hondas and most cars you know to cut out the 5 butterflies in side ours so.... hmmm... it can be done dammit, i just dont know the repercutions of it like how big is to big and vice versa well ponder on it all and lets get a soloution that way throttle response is crisper do to less moving parts ( keep it simple)
Rotary enthusiast
Joined: Mar 2006
Posts: 664
Likes: 0
From: Connecticut
how about at turboii hood with another scoop in front of where the stock air intake is, thus transforming the stock air intake into a cold air intake
that would be pretty sick, and it would probably look pretty badass too
that would be pretty sick, and it would probably look pretty badass too
Thread Starter
Banned. I got OWNED!!!
Joined: Aug 2004
Posts: 8,789
Likes: 2
From: Jacksonville, NC
Originally Posted by Secondmessiah
how about at turboii hood with another scoop in front of where the stock air intake is, thus transforming the stock air intake into a cold air intake
that would be pretty sick, and it would probably look pretty badass too
that would be pretty sick, and it would probably look pretty badass too
Originally Posted by torean
i'd go for a vmount that works with P/S
Senior Member
Joined: Jul 2005
Posts: 603
Likes: 0
From: FORT WAYNE
How about a water temp sensor pipe that has a bung for a temp gauge sensor that fits on one of the radiator coolant hoses. All you would have to do is cut the coolant hose in 2 pieces fit them on the ends of the pipe and remount. Something like this http://www.raretrick.com/index.asp?c...roductsID=7439
I R SAD PANDA W/O BAW
Joined: Nov 2002
Posts: 6,061
Likes: 1
From: bay area
Originally Posted by DASUPACAT1
How about a water temp sensor pipe that has a bung for a temp gauge sensor that fits on one of the radiator coolant hoses. All you would have to do is cut the coolant hose in 2 pieces fit them on the ends of the pipe and remount. Something like this http://www.raretrick.com/index.asp?c...roductsID=7439
Thread Starter
Banned. I got OWNED!!!
Joined: Aug 2004
Posts: 8,789
Likes: 2
From: Jacksonville, NC
I'll be posting an interest list for the front strut bars in a few minutes... We will be finishing the first batch of 10 this weekend, and we will start collecting payment Monday...
Last edited by 13b4me; May 17, 2006 at 04:42 PM. Reason: retarded grammar
Full Member
Joined: Apr 2006
Posts: 171
Likes: 0
From: Colorado
Headers/ downpipe and y pipe?
cold air box?
dual/ single side mount inercoolers and piping?
front spoiler/air scoop (underneath car)?
short shifter?
intake manifold?
Hey i know youre workin on the strut bars, but these ar all things that are just damn expensive for the fc, or just not available.
cold air box?
dual/ single side mount inercoolers and piping?
front spoiler/air scoop (underneath car)?
short shifter?
intake manifold?
Hey i know youre workin on the strut bars, but these ar all things that are just damn expensive for the fc, or just not available.
