using water as coolant?
i bought my rx7 recently and noticed that the 19 year old 'wigga' redneck that i bought the car from was using i think water as the antifreeze. is that bad for the rotors since i know you can use water for piston engines?
sorry the title should say using water as antifreeze |
you mean like straight water as coolant?
If so, you can....just beware that rust will occur in the system. |
Originally Posted by Black Knight RX7 FC3S
(Post 9707911)
you mean like straight water as coolant?
If so, you can....just beware that rust will occur in the system. |
The problem with water is it will begin to evaporate.
|
Drain it, refill with proper mix.
|
if the3 water is reddish-orange, that usually means the irons are rusting up, darker the color, the more rust there is in the cooling system.
To get rid of it would require multiple flushing. |
thanks for the reply.
|
You may want to do something fast before the temperature drops below freezing and your engine gets destroyed. I recommend flushing it really well and filling with a mixture of distilled water and ethylene glycol antifreeze (green not orange) as per the service manual. If you have extra time, it may not be such a bad idea to replace the thermostat while you are at it.
|
I agree with what everyone else wrote^^ one of the problems with using water instead of antifreeze is rust AND water has a higher freezing point and lower boiling point then antifreeze so it has a greater chance to freeze(destroying your system) or it will evaporate quicker and will not cool your engine down as well as antifreeze will. just flush out the system a couple of times and replace with antifreeze
|
it doesn't really destroy the engine.... that's what freeze plugs are for.
|
It can destroy the engine if all the water runs out of the blown freeze plugs once he starts the car unaware the water has frozen then thawed and the car overheats.
|
Buy 10 gallons of Distilled water, usually can be found for maybe a buck a gallon.
Then buy 4 bottles of those Prestone Radiator Cleaner stuff. Drain it, pour 1 gallon of distilled in first, then pour 2 bottles of those cleaner stuff into it, then add Distilled again until it fills up. Run your car for couple of days. Just drive it like normal. if you make short trips, try to drive 100 miles first. Drain it after about 100 miles Repeat the cleaner, drive, and drain again after your 2nd treatment, this time, pour nothing but straight distilled water into the system, again run it for another 100 miles or so. Drain, then add regular Anti-Freeze, depends on your location, minimum should be 30/70 (antifreeze/distilled) |
man, that is some overkill there, bet you could drink out of your cooling system nycgps, if both distilled water & antifreeze werent poison that is
|
Originally Posted by NYsNumba1Man
(Post 9709084)
will not cool your engine down as well as antifreeze will.
Originally Posted by eage8
(Post 9709092)
it doesn't really destroy the engine.... that's what freeze plugs are for.
Originally Posted by nycgps
(Post 9709320)
Buy 10 gallons of Distilled water, usually can be found for maybe a buck a gallon.
|
3 Attachment(s)
Freeze plugs won't help you if the block freezes solid.
Case in point, I just disassembled an engine on Tuesday that had frozen solid due to not enough antifreeze in the coolant. The starter would not turn the engine, nor would a long breaker bar on the front hub. During disassembly, the damage became obvious. After the water pump housing was removed and the engine turned over, oil began pouring from the cooling passages. https://www.rx7club.com/forum/attach...1&d=1262298311 The rear rotor was OK, but the front rotor was another story. The water froze in the center iron, expanded, and blew out the area just above the intake port. This locked the rotor in place and prevented the engine from rotating. Some of the cooling passage walls also broke off and fell into the oil pan. https://www.rx7club.com/forum/attach...1&d=1262298311 https://www.rx7club.com/forum/attach...1&d=1262298311 DO NOT RUN STRAIGHT WATER! Not only can it freeze and cost you an engine, but it also doesn't lubricate the water pump nor does it contain any corrosion inhibitors. |
holy crap
|
Originally Posted by Aaron Cake
(Post 9709480)
Freeze plugs won't help you if the block freezes solid.
Anyway, thanks for posting the pictures for the people who refuse to listen to me. |
Originally Posted by Aaron Cake
(Post 9709480)
Freeze plugs won't help you if the block freezes solid.
Case in point, I just disassembled an engine on Tuesday that had frozen solid due to not enough antifreeze in the coolant. The starter would not turn the engine, nor would a long breaker bar on the front hub. During disassembly, the damage became obvious. After the water pump housing was removed and the engine turned over, oil began pouring from the cooling passages. https://www.rx7club.com/forum/attach...1&d=1262298311 The rear rotor was OK, but the front rotor was another story. The water froze in the center iron, expanded, and blew out the area just above the intake port. This locked the rotor in place and prevented the engine from rotating. Some of the cooling passage walls also broke off and fell into the oil pan. https://www.rx7club.com/forum/attach...1&d=1262298311 https://www.rx7club.com/forum/attach...1&d=1262298311 DO NOT RUN STRAIGHT WATER! Not only can it freeze and cost you an engine, but it also doesn't lubricate the water pump nor does it contain any corrosion inhibitors. |
Originally Posted by Black Knight RX7 FC3S
(Post 9707984)
if the3 water is reddish-orange, that usually means the irons are rusting up, darker the color, the more rust there is in the cooling system.
To get rid of it would require multiple flushing. As was mentioned earlier, straight water carries heat better than a coolant/water mix. This is what I run at the track for just that reason. The problems with this setup are 1) lack of lubrication, and 2) freezing of the mixture and thus cracking the block. To deal with #1, I use a bottle or two of water-wetter, which will provide lubrication. To deal with #2, I drain some of the mix out in the winter and add in some ethylene-glycol (standard green stuff) to prevent freezing. Here is the mid-south, we'll only get a couple nights down in the single digits each year, so I don't need to add that much to the mix. In any case the solution is as the others mentioned - flush the system and replace with a proper mix of water/coolant. It doesn't get too cold up at Ft. Campbell, so you should be fine. Since you just bought the car I would recommend (if you have the time and facilities) to replace *all* the fluids, especially given the examples of "redneck engineering" you found in other area of the vehicle. Drain and refill the tranny as well as the diff. Good luck, -b |
Originally Posted by Evil Aviator
(Post 9709467)
You can flush the engine with tap water. I used a regular garden hose for a flush and then filled with distilled water / coolant as regular maintenance on my first new 13B engine, and the internals were nearly spotless when it was torn down 10 years later. My mechanic said it was the cleanest engine he had ever seen.
If someone is cheap about that 10 bux worth of distilled water, he/she shouldn't even own a car in the first place. Pure Water can carry A LOT more heat than any Pure Anti-freeze, I seen someone runs nothing but 100% EG anti-freeze and he wondered why his car overheats everytime he drives and he kept bitching at Toyota saying their car sucks ... rofl You need some Anti-freeze in the system because : to lube the water pump seals and most anti-freeze carries some sort of rust inhibitor to prevent rust. If you're 99.999% sure your area will never see freezing water temp, then you can run all distilled water + stuff like Water Wetter/ICE/etc. but some people over at the 8club said that WW/ICE does not do shit and might actually decrease the water's cooling ability. So use it at ur risk |
Originally Posted by nycgps
(Post 9710570)
Of course you could, but why would someone wants to add more minerals to an already fucked up cooling system? thats just asking for more trouble.
Originally Posted by nycgps
(Post 9710570)
Pure Water can carry A LOT more heat than any Pure Anti-freeze, I seen someone runs nothing but 100% EG anti-freeze and he wondered why his car overheats everytime he drives and he kept bitching at Toyota saying their car sucks ... rofl
|
Originally Posted by wrankin
(Post 9710478)
In any case the solution is as the others mentioned - flush the system and replace with a proper mix of water/coolant. It doesn't get too cold up at Ft. Campbell, so you should be fine.
-b |
I think you need some water + radiator cleaner to remove some of the shit in your cooling system.you got this car from some 18 yr old, well, god knows how long those water has been in that car.
Yeah, a lot of people on this forum run a 50/50 mix in 100deg weather and wonder why their 400hp engine is having cooling problems, lol. People usually up the power by 2-3 times but not doing a shit to the stock cooling system. then starts crying when the engine blew up. and who they gonna blame? Mazda. for some reason this happens a lot in the Rotary community. and this is why Rotary have such a bad name. |
Originally Posted by soldier_boi
(Post 9710614)
well i found out that there are also incompetent Jamaican mechanics. i got a coolant flush but mofo forgot to drain my reservoir and my coolant is now all slush. isnt a coolant flush include reservoir flush too?
It is usually better to perform the maintenance yourself as long as it is within your ability. Military DIY auto centers are great because there is a mechanic there to help guide your maintenance if necessary, and sometimes classes are available. Just make sure you have a ground guide when driving your car onto the lift. http://www.fortcampbellmwr.com/Recreation/autoCrafts/
Originally Posted by nycgps
(Post 9710630)
50/50 isnt really the problem, the lack of cooling is.
People usually up the power by 2-3 times but not doing a shit to the stock cooling system. then starts crying when the engine blew up. and who they gonna blame? Mazda. for some reason this happens a lot in the Rotary community. and this is why Rotary have such a bad name. |
Originally Posted by Evil Aviator
(Post 9710707)
It depends on the extent of the cooling problem. Sure, many other factors are in place, and the 50/50 mix is one of the factors that causes a lack of cooling ability. If that were not so, then racers would be running 50/50 as opposed to water. ;)
-b |
All times are GMT -5. The time now is 11:07 AM. |
© 2024 MH Sub I, LLC dba Internet Brands