Stock ECU Real-Time Tuning / Datalogging
02-09-15, 09:14 AM
#281
Senior Member
I find it easier to drop those alts out the bottom. Working on the daughter board on my lunch break today. I will let you know if I run into any hicups with the wiki
02-22-15, 08:38 PM
#282
Junior Member
Join Date: Jul 2014
Location: Ottawa, Ontario
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
have you looked to see if there are any hardware differences between the NA and TII ecus? It would be pretty sweet if we could change over with a reflash. Also could you shoot me the link to the wiki?
02-23-15, 03:59 PM
#284
Damn, how did I miss this thread!
Super cool to see you reverse engineer the ecu. I wish I was at that level.
It would be cool to have it run a canbus protocol outlet so stuff like a racepak dash hooked up to it. I've heard haltechs do that.
I really hate adding in extra sensors and want to try and grab signals from the ecu(Temp, boost,etc). I've been wanting to make a lcd touch screen gauge system run by an arduino. That way I can custom write the display and settings.
I'm currently running a S4 TII Rtek 1.7 chipped ecu but would totally buy another ecu to give this a try.
I do basic analog/digital stuff so I can help if you need in some way. I don't know coding very much but mess with arduino and led crap a lot so I work in eagle a bunch.
Super cool to see you reverse engineer the ecu. I wish I was at that level.
It would be cool to have it run a canbus protocol outlet so stuff like a racepak dash hooked up to it. I've heard haltechs do that.
I really hate adding in extra sensors and want to try and grab signals from the ecu(Temp, boost,etc). I've been wanting to make a lcd touch screen gauge system run by an arduino. That way I can custom write the display and settings.
I'm currently running a S4 TII Rtek 1.7 chipped ecu but would totally buy another ecu to give this a try.
I do basic analog/digital stuff so I can help if you need in some way. I don't know coding very much but mess with arduino and led crap a lot so I work in eagle a bunch.
02-23-15, 07:36 PM
#286
Super Raterhater
Thread Starter
iTrader: (6)
Join Date: Dec 2001
Location: NY, MA, MI, OR, TX, and now LA or AZ!
Posts: 10,624
Likes: 0
Received 2 Likes
on
2 Posts
There are some hardware differences between the S4 N/A and TII ECU. However, this is primarily in the sensors/drivers for things such as twin-scroll. If I get the AFM elimination stuff working well, you should be able to use either ECU on a turbo setup. You could probably still get away with it using the AFM by putting in turbo timing tables and adjusting the fuel accordingly.
As for the S4 N/A ECU progress, the boards are the same for each ECU so that part is already done. I have everything else more or less worked out that would be going on the S4 ROM, I just haven't actually sat down and did it yet since nobody is using one.
As for the S4 N/A ECU progress, the boards are the same for each ECU so that part is already done. I have everything else more or less worked out that would be going on the S4 ROM, I just haven't actually sat down and did it yet since nobody is using one.
02-24-15, 10:30 PM
#288
Super Raterhater
Thread Starter
iTrader: (6)
Join Date: Dec 2001
Location: NY, MA, MI, OR, TX, and now LA or AZ!
Posts: 10,624
Likes: 0
Received 2 Likes
on
2 Posts
Indeed, from what I've seen they run pretty much maxed at ~5psi @ 6K rpm or so. Of course, that's a poor measurement as it's dealing with CFM rather than pressure, but it's a rough ballpark of where they tend to max. One could always go MAF or something instead...
02-25-15, 11:04 PM
#289
Trunks are for corpses.
Join Date: Nov 2003
Location: St.Pete FL
Posts: 189
Likes: 0
Received 0 Likes
on
0 Posts
My car's not turbo. (Crazy, I know.) Right now it's got an rtek 2.0, which is fine for adjusting fuel/timing but i'd like to put some of these now-unused emissions solenoid outputs to better use (aux ports, vdi, etc.)
02-27-15, 08:19 PM
#290
Super Raterhater
Thread Starter
iTrader: (6)
Join Date: Dec 2001
Location: NY, MA, MI, OR, TX, and now LA or AZ!
Posts: 10,624
Likes: 0
Received 2 Likes
on
2 Posts
I've been making slow progress on the S5's. I'm in need of the N370 ROM -- I've got an N374 ROM already. Then i'll just need a S5 TII ECU to work with to locate all the necessary pins for the board modifications and such.
03-05-15, 05:31 PM
#293
Red Pill Dealer
iTrader: (10)
Eh... I got one too that I probably won't be using for a while. You can "borrow" it if you need to.
03-16-15, 09:01 AM
#295
Concerned Citizen
iTrader: (3)
Join Date: Nov 2001
Location: Miltown, WI
Posts: 699
Likes: 0
Received 0 Likes
on
0 Posts
So now that boards are out and warm, saltless roads are in the near future, will you be providing a link to your interface? I recall you were developing it, but never saw anything on the website for the PCBA's either.
03-16-15, 06:01 PM
#296
Super Raterhater
Thread Starter
iTrader: (6)
Join Date: Dec 2001
Location: NY, MA, MI, OR, TX, and now LA or AZ!
Posts: 10,624
Likes: 0
Received 2 Likes
on
2 Posts
The PC software? Yeah, I'll get a build made and put up on the wiki -- i've been trying to reorganize things to make the eventual S5 addition easier.
03-17-15, 06:36 PM
#297
Concerned Citizen
iTrader: (3)
Join Date: Nov 2001
Location: Miltown, WI
Posts: 699
Likes: 0
Received 0 Likes
on
0 Posts
Sonic,
Need some clarification, on PAGE 2 of this thread there is no mention of cutting the N332 "Pin 20" on IC604, and on the WIKI it asks to cut "Pin 20" (Or at least the graphic is confusing) There are no leads on the bottom side coming from Pin 20 (counting pins from #1 left to right) Which is correct?
Also, the trace you seem to ask to be cut looks to be the same as the pin we are wiring from Pin 6 on IC610. (Or what I'm considering "Pin 23"))
Can you clarify?
Need some clarification, on PAGE 2 of this thread there is no mention of cutting the N332 "Pin 20" on IC604, and on the WIKI it asks to cut "Pin 20" (Or at least the graphic is confusing) There are no leads on the bottom side coming from Pin 20 (counting pins from #1 left to right) Which is correct?
Also, the trace you seem to ask to be cut looks to be the same as the pin we are wiring from Pin 6 on IC610. (Or what I'm considering "Pin 23"))
Can you clarify?
03-17-15, 06:50 PM
#298
Super Raterhater
Thread Starter
iTrader: (6)
Join Date: Dec 2001
Location: NY, MA, MI, OR, TX, and now LA or AZ!
Posts: 10,624
Likes: 0
Received 2 Likes
on
2 Posts
Pin 20 is the pin with the wire soldered to it. There should be a trace coming from that pin moving to the left that will need to be cut.
04-06-15, 05:54 PM
#300
Super Raterhater
Thread Starter
iTrader: (6)
Join Date: Dec 2001
Location: NY, MA, MI, OR, TX, and now LA or AZ!
Posts: 10,624
Likes: 0
Received 2 Likes
on
2 Posts
Been rather swamped lately with work, so it's been slow going. I was trying to get some last minute patches in before dropping a version, but it's taking a bit longer than I hoped, so I'll just upload what I've got either tonight or tomorrow. It'll let you datalog/look at various settings/etc. Most of the saving back to the device is disabled currently as I was updating it for S5 support and savable tune support -- and the lack of feedback from a real car has been killer.