RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   2nd Generation Specific (1986-1992) (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/)
-   -   Oil Leak (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/oil-leak-614661/)

Gary# 01-16-07 10:39 AM

Oil Leak
 
Hi All,
My '88 RX-7 has developed an oil leak. :wallbash:
The oil appears to be leaking from the upper right side of the block - just behind and a little lower than the alternator mount. There is a small low spot on the block where the oil pools and then runs off. It leaks about a 1/2 a quart every 100 miles. In the 3 years I've owned it - it had never leaked more than a drop or two. What do you think is the cause???
Ohhh, and since I've never needed to take it to a shop before - please recommend a repair shop in or near Long Beach, Ca.

Thanks, Gary

Aaron Cake 01-16-07 10:51 AM

Uh oh. That sounds like a dowl leak.

Does the leak appear to be coming from between the housings? If so, then the only way to fix it is to disassemble the engine.

Gary# 01-16-07 11:38 AM

Yep. I think it is...
I wipe up the oil, start it, & within a minute the oil is back.
Where should I take it for repair??? somewhere close to Long Beach, Ca. I hope.
Thx, Gary

Valkyrie 01-16-07 12:25 PM

I'd try wiping it off (with the car off that is), and put some ultra black (oil resistant) RTV (or some other type of non-permanent sealant) on there, then let it cure for 24 hours (meaning don't turn the car on), and see if it still leaks (it probably will, but it's worth a shot). Unless it's a pressurized leak, in which case I wouldn't bother.

Of course, this is a band-aid fix for what amounts to open heart surgery if you were gonna fix it right...

Gary# 01-16-07 11:19 PM


Originally Posted by Valkyrie
I'd try wiping it off (with the car off that is), and put some ultra black (oil resistant) RTV (or some other type of non-permanent sealant) on there, then let it cure for 24 hours (meaning don't turn the car on), and see if it still leaks (it probably will, but it's worth a shot). Unless it's a pressurized leak, in which case I wouldn't bother.

Of course, this is a band-aid fix for what amounts to open heart surgery if you were gonna fix it right...

---
I like your McGyver approach. And then add the fact that I don't know dik about nuttin' what don't have pistonz. But hey - what the hell - it's my wifes car - :)
One way 2 find out without :Kill1:
---
So lets say I apply the ultra black & when I give it a go it leakz...
Is band-aid repair (stage 2) JB WELD :MissileSm
Thx, Gary

Valkyrie 01-16-07 11:37 PM

I personally wouldn't want to put JB weld on anything that will some day need to be taken apart, though... although it probably wouldn't hurt if it was a small amount.

Aaron Cake 01-17-07 08:56 AM

You won't be able to seal it with anything. :(

Gary# 01-17-07 10:37 AM


Originally Posted by Aaron Cake
You won't be able to seal it with anything. :(

---
I'm sure your right. :slap:
Last nite I found two local repair shops:
Rotary Racing in Santa Ana, Ca.
and
Rod Millen MotorSports in H. B.
---
Anybody have experience could you rate either of these two shops??? Gud or bad...
I know I need to get 'r fixed. I don't want to take it to a hack.
Thx,


All times are GMT -5. The time now is 04:14 AM.


© 2024 MH Sub I, LLC dba Internet Brands