RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   2nd Generation Specific (1986-1992) (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/)
-   -   Fuel pressure help (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/fuel-pressure-help-1011086/)

sclas90 09-09-12 07:18 AM

Fuel pressure help
 
I was wondering what fuel pressure I should run on my aggressively street ported s4 t2 running on 9 psi? I have an aftermarket fuel pressure regulator and my fuel rails are modded to use it. also have 3" exhaust and fmic piping and a 255lph walbro but with stock 550's :(

misterstyx69 09-09-12 09:16 AM

43 psi sounds good.

Evil Aviator 09-09-12 10:30 AM

It's not such a good idea to try to keep your engine from blowing by simply raising the fuel pressure. What you really need are some larger fuel injectors and an aftermarket fuel computer.

With the Walbro, I don't think that you will be able to raise the pressure enough for your engine. However, I am guessing that you will be able to run about 50-55psi before there is a flow loss. In theory, 50psi should support about 300hp on the stock injectors, but there are a lot of factors like the quality of the electrical connection to the fuel pump, condition of the fuel injectors, engine tune, turbo efficiency, fuel system flow losses, etc. I think that you are going to fry your engine, but good luck.

RotaryEvolution 09-09-12 11:58 AM

and you still are running pig rich out of boost.

popping an engine is mandatory for the learning process.

K-Tune 09-09-12 12:35 PM

Worst part of the whole equation is that full 3" exhaust...best way to blow a motor. With the ported motor and S4 wastegate you will be way over 9psi in the 5-6,000rpm range.

Want to run stock injectors? Run stock boost and stock exhaust. Otherwise you need to do something else if you want the motor to last.

Evil Aviator 09-09-12 12:41 PM


Originally Posted by RotaryEvolution (Post 11215769)
popping an engine is mandatory for the learning process.

Dang, that means I haven't learned anything during the 24 years that I have owned RX-7s. :(

RotaryEvolution 09-09-12 12:57 PM

lucky! i went through a few learning the tuning process on turbo rotaries. but that was also before there was bible sized threads about what to do and not to do.

most people now want you to hold their hand through the whole process for nothing but a few kind words. dang, i'm sounding bitter... probably because i've typed it all out god knows how many times and the info is still out there.


#1, fuel pressure is a bandaid for properly sized injectors. moving up much further requires a way to tune fuel.

of course i've seen these threads more than i care to remember, upgrading everything that shouldn't be upgraded before upgrading the things that should be, like fuel system and engine management. yes, they are the most costly parts to accumulate, they are also the most important.

sclas90 09-09-12 06:49 PM

It never boosts over nine lbs in any gear even at high rpm wot. Its closer to seven unless I'm at 6500 wot. Injectors and ecu are next and I know that's important. My friends car has the same setup on 10lbs and he was running like 60psi but that seems wacko to me. So 43?

sclas90 09-13-12 11:02 PM

Or higher?

K-Tune 09-13-12 11:22 PM

Without a wideband you're only guessing, so guess away. We can't tell you what the best fuel pressure will be.

sclas90 09-13-12 11:26 PM

True, just thought somebody had the same mods and a wideband too. nvm


All times are GMT -5. The time now is 06:04 PM.


© 2024 MH Sub I, LLC dba Internet Brands