click but wont start..
#1
click but wont start..
heres the problem. i just got my engine install.. its a rebuilt one..i start it once but i forgot to put the egi comp fuse back in and its also low battery too...then i put in a new battery and it would just click... i wont turn over...and i also put the fuse back end... it wont start. it would go click click click...
#2
rotary tech
iTrader: (9)
Join Date: Jan 2007
Location: tracy/stockton ca
Posts: 795
Likes: 0
Received 0 Likes
on
0 Posts
sounds like your starter i had the same exact problem. went through buying a ignition switch(didn't fix it). new wiring harness(didn't fix it). then i finally bought a starter(never had a problem again). i did run new wiring to it as well but that because i relocated my battery. it may test good mine tested good for the 5-6 times i had it tested, but put in a new one. try running a new power wire first as it will be cheaper to try that. then if no fix buy a starter let us now how it goes
#7
rotary tech
iTrader: (9)
Join Date: Jan 2007
Location: tracy/stockton ca
Posts: 795
Likes: 0
Received 0 Likes
on
0 Posts
yeah even a bench test can prove good my starter engaged and spun like crazy i thought but i think it was just worn out and when it hit the fly wheel it couldn't turn under a load you know what im saying and thats all mine did was click click them saying "wtf is wrong" actually try tapping the back of the starter with like a ball peen hammer while some one is trying to crank it just an old school trick i learned from my dad. some time the starter brushes rust and sieze and if you give it a good tap it could break it loos and work if it does it just get another starter cuz it will sieze again.
Trending Topics
#8
Caramelldansen
Join Date: May 2005
Location: SF Bay Area, California
Posts: 1,182
Received 0 Likes
on
0 Posts
Get under your car and hit the starter with a hammer, just a good thump. If it then proceeds to work again the starter is basically done and should be replaced (hammer trick seems like a diagnostic measure instead of a treatment).
Or so I've heard ....
Or so I've heard ....
#10
my dad told me to hit it anywhere...i tried that too but ill try again.... i want to get it start tomorrow so i can ride it to work. but its that not working then ill get up early tomorrow and took it off then take it to autozone and test it.....For the spark plug wire does the 1 stand for the front rotor and the 2 stand for the rear or is it the 2 and stand for the front rotor and 1 stand for the rear..
Last edited by rx7-kid; 04-15-07 at 04:10 AM.
#11
rotary tech
iTrader: (9)
Join Date: Jan 2007
Location: tracy/stockton ca
Posts: 795
Likes: 0
Received 0 Likes
on
0 Posts
let us know im betting it tests good. but when you put it back in it may start up but if it does turn it off and try again. as mine started up but my car died after(new motor i was working with) i went to turn the key again and CLICK!!. i was pissed it would do this everytime i would get it tested and put it back in. im saying test it more then once so you don't think its fixed go to work and get stranded lets us know though i do recommend just getting a starter but hey it may be something else
and get it tested at more then one place as in take it to kragen as well and maybe another auto parts store the more people you can get to test it the better
and to the other question front rotor= #1 rear rotor= #2
and get it tested at more then one place as in take it to kragen as well and maybe another auto parts store the more people you can get to test it the better
and to the other question front rotor= #1 rear rotor= #2
#12
thanks..im working tomorrow at 11:00 and will be off at 7:30....untill then im going to do everything that i could.....want to ride my Rx7 again...miss the feeling of riding it.....it handle and respond better and also accelerate faster than my dad truck which i have been driving around in it..
#13
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
stated you have a low battery..try it Fully charged.(or switch for a good battery)if the battery is below 11 volts the Engine won't start..you will get the clicks you are talking about...**** Rereading now..Check the Ground going to the Bell housing,Follow the main wire with the stripe from the battery to the Block.Also check the fuse block engine bay,the main wire there.and another thing is make sure the wires are on at the starter correctly.Try also to Tap the solenoid on the starter.and finally give the Main relay(silver box by the Sec coil) a Tap...it does sound like starter too,though,,can you throw a used one on to compare?
#14
Lives on the Forum
iTrader: (7)
To the previous poster, he said he got a new battery.
I had a similar problem. It would just click at me, but when I took it off it tested fine. It turns out that the wires on the battery terminals were badly corroded. I took them apart and cleaned them and it works fine now.
Here is my thread: https://www.rx7club.com/2nd-generation-specific-1986-1992-17/need-help-diagnosing-starting-issues-already-searched-637903/
I had a similar problem. It would just click at me, but when I took it off it tested fine. It turns out that the wires on the battery terminals were badly corroded. I took them apart and cleaned them and it works fine now.
Here is my thread: https://www.rx7club.com/2nd-generation-specific-1986-1992-17/need-help-diagnosing-starting-issues-already-searched-637903/
#15
ok i know why i click but not turn over...it was because the battery i switch too was weak and doesnt have enough volt to turn it....now i put in another one.....this time it would turn over but wont start.....i tried unflooding it and still wont work...or was it still my battery was too weak....when i have my old engine with that weak battery it would still crank and start but i wont do that on this rebuilt one.....the one that in the car now was 660cca and 800ca.. the one that is with the car was 725cca and 990ca....here's my plan for now...take my old battery to autozone and charge it before i go to work and then when im off ill go pick it up and put it in...hopefully this time it will start....since it more powerfull than the other two...
#16
alright heres the problem right now....i will get it to start if i do that thing where i push the car to where its fast enough and then let go off the clutch while still on gear 1 but then heres the problem....once its runnning and get it to where its hot enought it would just die down...when i crank it i feel like it was trying to start but wont start...could it be that my tps is off..
#18
i did push start it and got it to start...but when it warms up then it just die off. it just die off.....theres a black wire that branch off from the wiring harness that is close to the wire that connect to the alternator.....i forgot where that piece go...
#19
rotary tech
iTrader: (9)
Join Date: Jan 2007
Location: tracy/stockton ca
Posts: 795
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by rx7-kid
i did push start it and got it to start...but when it warms up then it just die off. it just die off.....theres a black wire that branch off from the wiring harness that is close to the wire that connect to the alternator.....i forgot where that piece go...
#20
I break Diff mounts
iTrader: (1)
First clicking issue.
Your battery terminal connections need to be checked. Clean them and tighten them down.
If it still doesn't work then check your starter connections before thiniing it's iginition switch.
Running issue.
First check with a mutlimeter that you are getting 13+ volts. If not then your just running off the battery and it'll eventually conk out.
how long does it run? if only a few seconds then maybe the AFM isn't connected(and your just running of fuel priming).
Then check your manual idle screw on the top back of the TB. Make sure it's not missing or screwed high enough to keep the motor idling.
THen maybe you've fowled the spark plugs. A fresh set may help the situation.
If it doesn't start via starter cranking then check your timing. I had mine off so bad that it would only run via push starting.
Your battery terminal connections need to be checked. Clean them and tighten them down.
If it still doesn't work then check your starter connections before thiniing it's iginition switch.
Running issue.
First check with a mutlimeter that you are getting 13+ volts. If not then your just running off the battery and it'll eventually conk out.
how long does it run? if only a few seconds then maybe the AFM isn't connected(and your just running of fuel priming).
Then check your manual idle screw on the top back of the TB. Make sure it's not missing or screwed high enough to keep the motor idling.
THen maybe you've fowled the spark plugs. A fresh set may help the situation.
If it doesn't start via starter cranking then check your timing. I had mine off so bad that it would only run via push starting.
#21
I break Diff mounts
iTrader: (1)
Originally Posted by fcforlife
most likely that plugs goes into the ack of the alternator look at the back of it it should have a place to plug into and for the stalling read the fsm it will have some trouble shooting pages in it that explain hot start problems
I'm assuming this is S4.
Thread
Thread Starter
Forum
Replies
Last Post
poop2003
3rd Generation Specific (1993-2002)
1
09-21-15 10:28 PM