RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   2nd Generation Specific (1986-1992) (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/)
-   -   Charcole canaster junk. (https://www.rx7club.com/2nd-generation-specific-1986-1992-17/charcole-canaster-junk-294696/)

Dom_C 04-14-04 03:03 PM

Charcole canaster junk.
 
i realize i probably spelt charcole canister wrong but oh well. any ways. i was out looking at my 86 NA today and noticed that there is a tube that goes into the bottom of the charcole canister but looks like it has been cut it's just dangling there. where is this tube supposed to go? thanks
Dom

Rxmfn7 04-14-04 03:04 PM

Its supposed to be like that..

Dom_C 04-14-04 03:06 PM

oh yea, also the wire on top of the o2 sensor? where is that supposed to connect to? mine doesn't connect to anything and is only like 4 inches long. thanks

Rxmfn7 04-14-04 03:07 PM


Originally posted by Dom_C
oh yea, also the wire on top of the o2 sensor? where is that supposed to connect to? mine doesn't connect to anything and is only like 4 inches long. thanks
There should be a green connector coming out of the wiring harness for the 02 Sensor. Look for it dangling around somewhere.

Dom_C 04-14-04 03:11 PM

is it a greeen three prong connector? i know there is a green connector around where the fuel pump tester connector is and it isn't connected to anything coudl this be the one?

Derek10AE 04-14-04 03:18 PM


Originally posted by Dom_C
is it a greeen three prong connector? i know there is a green connector around where the fuel pump tester connector is and it isn't connected to anything coudl this be the one?

It will be a single wire with a single prong connector. I believe it splits from the main harness around the thermostat housing.

Rxmfn7 04-14-04 03:19 PM


Originally posted by Dom_C
is it a greeen three prong connector? i know there is a green connector around where the fuel pump tester connector is and it isn't connected to anything coudl this be the one?
No.. is there a green connector on the end of the wire coming from your O2 sensor? If not, it was cut and youll be needing to do some splicing probably. Ill try and find a pic of the connector, its just a 1 pin slide on type connector.

oakback 04-14-04 03:23 PM

On top of the engine block, on the driver's side, the wiring harness goes sorta below where your BAC valve is. A wire comes out around there, and (at least mine does) goes under your UIM and comes out over the tranny. There should be a small green connector as mentioned above on the end of this wire. Mine came off, so I just crimped on a spade type connector that I had laying around, just in case I had to disconnect it for any reason, without having to cut it.

WAYNE88N/A 04-14-04 06:27 PM

if you only have 4" of wire coming from the old O2 sensor, might as well buy another one (Bosch makes 'em for our cars)- the wire is a special shielded type to inhibit electrical noise...if you just splice in regular stranded wire, might have a funky signal going back to the ECU...

Dom_C 04-14-04 07:06 PM

does anyone have a picture of the correct setup? just so i can see waht wire to connect to. and thanks i will pick a new one up soon. thanks
Dom


All times are GMT -5. The time now is 01:36 PM.


© 2024 MH Sub I, LLC dba Internet Brands