turbo 2 brakes
i am getting the respeed front brake adaptor for tubo 2 brakes on an fb
my question is has anyone done all 4 brakes from a turbo 2 on an fb rear included. i have a fabricator making rear brackets for me. its going in a 84 gs the question i have is do i need the turbo 2 master cylinder, brake booster, proportioning valve? |
If you get the GSL-SE rear brakes, you'll have virtually the same thing, no fabrication required. I compared the two setups many years ago, and if memory serves me right, the rotors, pads, and caliper bore were identical between the -SE and the FC.
|
I've seen pics of a FB with TII brakes all around, not sure about the MC or anything else.
|
i have a ford 9" rear the gsl-se brakes are actually harder to fab a mount for
i may just get a proportioning valve from the fc |
I have 10.5" Ford rear brakes on mine, with 310mm Wilwood in the front. I'm using the FC master cylinder and booster, it has a 15/16" bore and a much larger booster. You need to mount it with a 10mm spacer on the firewall, but all the bolts are in the same place. You will definitely need to swap the master cylinder if you're using FC front brakes.
http://javert.orcon.net.nz/diff4.jpg Feel free to PM me if you need help, I've spent months getting this right. |
yea i bought the turbo 2 master cylinder, and propotioning valve today. what kind of spacer did you use
do you have a pic? thanks |
Nah it's all bolted up and hidden.
If you can picture the back of the booster with four long studs that go into the firewall, I simply used some 10mm box section steel and created a square spacer that connects all the studs. I guess a more professional way would be to get a slab of 10mm thick alloy and cut the centre out, but my way works and is cheap. You will also need to grind a small amount of material out of the clutch master cylinder as it will hit the new booster. I understand this is all you need to do with LHD cars, but as mine is RHD I also needed to slot the master cylinder holes on the firewall a small amount. I'm not sure why RHD has less tolerace than LHD, guess only Mazda knows that ;) |
I am replacing my rear 4-Piston calipers, with TII rear brakes rotors and calipers. I am using a 94? Mazda 929 Master Cylinder with No ABS.
It is a larger Master than the TII or the FD. I putting the smaller brakes to lower pedal travel, and regain my parking brake that I lost when I swapped the Ford rear in. |
Originally Posted by Directfreak
I am replacing my rear 4-Piston calipers, with TII rear brakes rotors and calipers. I am using a 94? Mazda 929 Master Cylinder with No ABS.
It is a larger Master than the TII or the FD. I putting the smaller brakes to lower pedal travel, and regain my parking brake that I lost when I swapped the Ford rear in. I've been told that the TII unit I have will be "borderline" in terms of pedal travel, but worst case scenario I'll do exactly as you're planning and swap in a 929/Cosmo unit. |
thats why im adapting the turbo 2 rear setups to the 9 inch, it wont be that bad
i have a turbo 2 mc and p-valve so the brakes will balance the booster in the fc and fb are the same part numbers so the mc should be a bolt in swap but ill have to witness that when i get to that point i guess |
the 929 unit is a direct bolt in in fd's i believe what about fb's
|
i should be fine with the turbo 2 mc and turbo 2 brakes all the way around, the way i look at it.
|
Originally Posted by monster7
the 929 unit is a direct bolt in in fd's i believe what about fb's
I can assure you the FC booster I have is completely different to the FB unit. The only similarity is the stud pattern where it bolts up to the firewall, the rod length and diameter of the booster is very different. |
Im also running a TII booster and MC.The booster bolts right up if you use 2 of the factory aluminum spacers under it.Then you have to grind a little material off the side of the clutch master for clearance.
I run 12" front discs with TII calipers from Selectmaz and stock SE rear brakes. |
yea i just double checked, and i made a mistake they are different part numbers,
SOMETIMES I ACTUALLY DO MAKE A MISTAKE, go figure i have an auto so the clutch master doesnt exsist thanks for yalls help |
and i just bought the turbo 2 booster also
|
I am running an N/A FC Booster - because the TII was too large.
Originally Posted by monster7
i should be fine with the turbo 2 mc and turbo 2 brakes all the way around, the way i look at it.
Although I have to modify them to fit my rear. |
Originally Posted by Directfreak
I am running an N/A FC Booster - because the TII was too large.
That's what I will end up with in a month or so.. Although I have to modify them to fit my rear. |
i know the gxl and the verts come with the turbo 2 brakes, thats why i was asking and i figured they would be the same.
|
yo wattup ?
how muche the sport prakes sistem if I want buy't from U.S.A becous am from Saudia Arabia ??? thanks... |
Originally Posted by saudiarx7
yo wattup ?
how muche the sport prakes sistem if I want buy't from U.S.A becous am from Saudia Arabia ??? thanks... we are talkin about puttin turbo 2 brakes on an fb. |
I now am just asken aboaut the brakes becous am all reday make the turbo 2 brakes in my baby becous it's now 700 RWHP , OK ...
ThAnKs ... :) |
how about some grammer lessons. and about cost i have no idea. it will probably cost you more than the brakes are worth to get them to you.
mainly if you are truely making 700rwhp you need more than turbo 2 brakes. |
yes of cours I thinkin about HKS praks of Toyota sopra if i swap't in my baby , what do thenk ?
|
Originally Posted by saudiarx7
yes of cours I thinkin about HKS praks of Toyota sopra if i swap't in my baby , what do thenk ?
|
All times are GMT -5. The time now is 06:42 AM. |
© 2024 MH Sub I, LLC dba Internet Brands