One thing you could try is pulling it with another car and popping the clutch. It's worked for me. The only issue is that if it's stuck because of a broken seal, you could cause damage to the rotor housing.

Sounds like you are running out of options, if you can't break it loose with a reasonable amount of torque on the breaker bar chances are things are pretty serious in there.

I told you about the happy news with the 12A in that silver GSL but I didn't tell you about my most recent experience, with the locked up 12A in my current 83 LE. That one would not break loose and on the tear down I found things were pretty messed up inside but the engine had 147,000 miles on it so not unexpected.

In your case since the engine was a recent rebuild there's a good chance you still have lots of reusable parts, even a couple good rotors and rotor housings if you're lucky. So think about what KC said, you could get radical and tow it but you would you also run the risk of destroying some of the innards, rotor housings being the greatest loss.

If it were me I'd give up and tear it down. Taking a 12A apart is actually a lot of fun, kind of like a treasure hunt to see what good stuff you might find inside. And if the car is a keeper it's going to be well worth popping a fresh rebuild in there, I have one in my current daily driver LE and it's the sweetest FB I've had yet. A couple of rotary friends (Robert and Mike) and me did that rebuild in Robert's basement, took a day or two but it came out fine.

Are you trying to turn both directions? Is the engine bolted to a stand or immobilized in some way/ What is contraption you speak of?

It's on an engine stand. I connected a puller to the flywheel and I put a breaker bar in the middle. I tried it both ways. I guess I could get a longer moment on it, but the stand is only going to be stable with so much force. I'm happy to share pics if that helps. Also, you can see gunk when you look inside the exhaust port. It looks pretty nasty in there. I only my myself to blame for that.

I don't think I've ever seen a rotary exhaust port without gunk in it. Have faith and pray to the Rotary Gods.

If you have a sturdy 1/2" breaker bar (2 feet or better) fitted with a 19 mm socket you can connect this directly to the eccentric shaft bolt to get better torque.

The puller you have on there may be flexing and buffering the torque so you're not getting enough to break whatever is locking it up, which could be just a bit of carbon wedged in an apex seal just right.

Being on the stand instead of in the car also makes it harder to get good sharp torque on the eccentric bolt. Anything you can do to stabilize the engine and stand will help.

Be sure to rock and torque the breaker in both directions like GSLSEforme says with good sharp force in both directions.

And if that doesn't work, well see my comment a couple posts above.

To Ray you listen; as yoda would say.

Tear it down. You already have the oil pan off... what's stopping you now?

man i was hoping you could break it free, but its looking like you may need to actually pull her apart..

It does sound like fun, but to answer the question "what's stopping me now?" about $1000 for a rebuild kit and the fact that it only has a few thousand miles on a professional rebuild. I just hate to do it. I don't need the car right now (but it would nice to have for my long commute rather than my old land cruiser @ 14mpg ). AND I don't do well with knowing when to quit. I was ready to break it down when I started this thread but I was persuaded to try to revive it and now I don't want to quit on her. But if I need to, I need to. I just don't want to stop short.

I'll give it another go with a 19mm breaker.

If you don't damage the apex seal/side seal/corner button or whatever is the hold up.... The soft seal kit is $150 from Rock auto. Most of the innards (if it was professionally rebuilt) should be new if not in immaculate shape.

Mr. Morgan, I consulted the Rotary Gods and they told me your 12A may be worthy of Resurrection.

So give that breaker bar one more chance, with the engine tied down as good as you can get it.

Also it will help if you use a mantra while torquing on the breaker bar.

Kind of like the Om chant, but the Rotary Gods would prefer Zoommmm..... , that really gets them excited.

Pay attention to the frequency of your torquing and cue it to your Zoommm mantra, I would recommend 432 Hz:


I'm serious, this is what worked for me.

Let your mind wander into the rotor chambers as you chant and torque, imagining yourself as a tiny fleck of carbon striving to be free.

Ray,lol...

Ommmmmm ... Ommmmmm ... Ommmmmm ...

Perfect timing - I just finished reading "The Alchemist". I will listen to my heart for the story of my legend which is to again drive this car - or something like that. I can't promise my mantra won't be more aggressive than a "vroom" sprinkled with some expletives.

Well, I tried and tried. I chanted vrooom and oom and some other choice words. At point I had a pry bar as a brace and I brought my engine hoist into the mix. No go.

I gave in and broke it down. It was all gunked up inside and I now have the shaft turning by hand.

I see two seal kits on Rock Auto. Anyone know the different beside $30?

Man, was it easy to tear down! Thank you all for the help and words of encouragement. Guess I'll get to reading!

Thank you,

Brandon

Unfortunate you couldn't get engine to turn,now you'll know your car from the inside out!

Make sure you get those seals to sit right. Sick when you pinch on putting the plates on😂

Tearing down a 12A is almost as much fun as getting a 12A to run without tearing it down.

Consider it the beginning of a Great Adventure.

Do you have pictures of your innards? I'm curious to see what your housings and rotors look like, they are the critical parts.

I'm curious too about the aftermarket 12A soft seal kits on RockAuto and some other sources.

It's always safer to go with the Mazda OEM stuff when in doubt but they cost a lot more and if the quality is no better I'd rather save the money.

Does anyone know first hand?

The fel pro kit for a 12A on RA is all I ever use in my 13Bs. I just toss the intake gasket and cut the exhaust gasket in half to suit the 13B.

They are the same style as OEM mazda. Red with white stripe inner coolant seals and black solid rubber outer coolant seals. Viton oil control rings are red for some reason, but never had an issue with oil consumption.


https://www.rockauto.com/en/moreinfo...192272&jsn=356


I see there is a Mahle kit available now. Never used that one. I don't think I ever will being that the Felpro kit is good and cheaper.

I bought the fel pro kit.

The innards were interesting. After I got the gunk off the first rotor (the rear one), the cam rotated. It looks like the seals are just caked with whatever. i'll get some better pictures, but this is what I have. Please excuse the mess - I need to reorganize my work area. And please excuse the size of these pictures. Maybe someone has a tip on how to attach in a more friendly size.

https://cimg8.ibsrv.net/gimg/www.rx7...b0e988dc02.jpg
https://cimg2.ibsrv.net/gimg/www.rx7...1f61790ff4.jpg
https://cimg4.ibsrv.net/gimg/www.rx7...c56923fb53.jpg

Damn, its a good thing you didn't get that running... Think about all that rust and nasty spinning around in the housings?!? I don't think you would have held compression for long if at all.

Need to clean them off, and take better pictures, but from a cursory glance they look good.

Great thing it didn't budge. From the pictures housings look ok. Rotors will clean up! She's gunna be back and better then ever good find!

Check for pitting on the irons. Careful removing the seals from the rotors.... They do look crusty you might break a seal getting them out, but the rotors could be alright with a good cleaning.

Yeah this is fun. Anything I should consider doing while I'm in here? My parts will be in on Thursday. I hope to be able to start the rebuild this weekend. I have watched Aaron Cakes rebuild videos. Anything else I need to watch out for?

The seals look caked. Can you by individual seals? I've only seen the entire kits on atkins.

Yes you can buy individual side seals, Atkins has them and I see them come up every once in awhile on ebay.

https://www.atkinsrotary.com/store/1...1-23-151A.html

They have the springs too:

https://www.atkinsrotary.com/store/7...20-11-317.html

And the apex seals and springs:

https://www.atkinsrotary.com/store/A...t-ARE12-3.html

But word of caution, each side seal needs to be custom fit to exactly the right length with the proper curvature at the ends to seal properly.

For this reason they say if your old seals are good keep track of where the came out and put them back in the same place.

Easy to say, hard to do.

Check out this rebuild post for details, by the Great Alabama Rotary God Robert Watson:

https://www.rx7club.com/1st-generati...k-12a-1061516/

Just get the kit from atkins for the apex seals and springs. Six seals, six apex springs long, and six apex seals short. You will NOT regret this. $400 now is better than buying another soft seal kit cause you can't get compression out of the old springs and seals. I've tried re-using old apex seals; I couldn't get them to seat right. But I've never had issues with buying a new set from Atkins.