RX7Club.com - Mazda RX7 Forum

RX7Club.com - Mazda RX7 Forum (https://www.rx7club.com/)
-   1st Gen General Discussion (https://www.rx7club.com/1st-gen-general-discussion-207/)
-   -   So what caused this rotor's death? (https://www.rx7club.com/1st-gen-general-discussion-207/so-what-caused-rotors-death-766715/)

Jeezus 06-25-08 07:20 PM

So what caused this rotor's death?
 
http://i29.tinypic.com/2q3atub.jpg


First person right wins a cookie :D

CrackHeadMel 06-25-08 07:21 PM

did this occure in an engine, or did you doom this rotor by other means

©ØÐËߣüË 06-25-08 07:28 PM

draged by a car or truck

yetterben 06-25-08 07:37 PM

E-shaft broke in 2

djessence 06-25-08 07:38 PM

apex, since its the same rotor as bad83's thread

blackdeath647 06-25-08 09:20 PM

yeah i would go with the apex simply because i can't think of anything else that would "pop" off and cause that much damage, if it was an e-shaft i'm sure there would have been a LOT more damage :P

yetterben 06-25-08 09:24 PM

i called and found out we are all wrong lol!

blackdeath647 06-25-08 09:31 PM

soooooo? what was it?

yetterben 06-25-08 09:35 PM

i cant tell that would be no fun for you guys!

blackdeath647 06-25-08 09:44 PM

a bolt or screw that accidentally got in the engine through the carb/intake?

JSmith0101 06-25-08 09:51 PM

A hammer got sucked into the intake?

dbragg 06-25-08 10:01 PM

did you throw it down the grand canyon?

orion84gsl 06-25-08 10:04 PM

Definitly a stick of dynamite

blackdeath647 06-25-08 10:12 PM

the hamster running inside it got tired fell asleep and fell off, then it was brutally mutilated .... i'm talking about the rotor cuz the hamster must have been all jacked up on steroids.
http://vids.myspace.com/index.cfm?fu...deoid=26089251

Jeezus 06-25-08 11:51 PM


Originally Posted by wotnartd (Post 8319061)
A hammer got sucked into the intake?

Close enough :D

http://i32.tinypic.com/2n02cer.jpg

Jeff20B 06-26-08 01:20 PM

That was an '83-'85 rotor. I hope you had fun.

t_g_farrell 06-26-08 02:36 PM

You dropped it!

See thats what I get for guessing before reading the whole thread. You beat the living crap out of it with BFH. I hope you feel better now.

Jeezus 06-26-08 02:59 PM


Originally Posted by Jeff20B (Post 8320888)
That was an '83-'85 rotor. I hope you had fun.

We did. It was a blast. It was unusable so we didn't bother cleaning it off.

Trivia Question 2:

If this was a real engine, what would be the problem with it?
There may be more than one answer...

http://i31.tinypic.com/2enrfhf.jpg

Rogue_Wulff 06-26-08 03:03 PM

It wouldn't fit under the hood of an FB......

dbragg 06-26-08 03:06 PM

stu, you need to do less, or more, drugs :)

bad 83 06-26-08 03:06 PM


Originally Posted by Jeezus (Post 8321211)

Trivia Question 2:

If this was a real engine, what would be the problem with it?


http://i31.tinypic.com/2enrfhf.jpg

We didn't put it in the SA?!?!?! :D

bad 83 06-26-08 03:09 PM


Originally Posted by t_g_farrell (Post 8321139)
You dropped it!

See thats what I get for guessing before reading the whole thread. You beat the living crap out of it with BFH. I hope you feel better now.

Well.......I found one of my gaskets was damaged, so I took one of my scrap rotors and vented some flustration. I let Stu have a little fun with it too.

yetterben 06-26-08 03:14 PM

You dont have 5grand to buy the shaft or the bolts. lol Answer two is big dreams lol. Don'y say there is to many center irons lol



DO IT!!!!!!!!!!!!!!

TheRX7Project 06-26-08 04:41 PM

There's no oil in it. I can tell because it's not leaking.

680RWHP12A 06-26-08 04:48 PM

looks like it would take alot of oil with all those oil fill holes

i could see 2 s5 turbos bolted up to that beast along with 2 boosted nikki carbs for fueling duties ;)
oh and a big block of cheese on top


All times are GMT -5. The time now is 05:06 PM.


© 2024 MH Sub I, LLC dba Internet Brands