View Poll Results: Which model would you be interested in?
Classic Cup Holder (Power mirror & switch)
22
62.86%
Dual Switch Cup Holder (Two switches)
8
22.86%
Centered Cup Holder (No switches)
5
14.29%
Blank Panel
0
0%
RX7 Logo
2
5.71%
Switch Blanks
2
5.71%
Multiple Choice Poll. Voters: 35. You may not vote on this poll
[For Sale] FC Cupholder Panel (COMING SOON/INTEREST GAUGE THREAD)
#1
FC Cupholder Panel (COMING SOON/INTEREST GAUGE THREAD)
Howdy guys and gals, as a new forum vendor, it is a great opportunity to now show off the panels I have been designing. I am currently awaiting what I genuinely believe will be my best and final prototype. These will hopefully be for sale in late January to early February. I am looking to see who would be interested and what your thoughts are!
These panels are extremely thick and durable (still sit about .025" below the surface of the center console like the OEM panels) The clips are MUCH stronger than the thin and fragile OEM ones. The design will clip into the OEM holes and be removable just as the OEM panels are.
The potential models are:
1. Classic Cup Holder
2. Cup holder with two switches
3. Centered Cup holder
4. Blank panel
5. RX7 Panel
6. Switch blank
I will also be making the switch blank with custom sized holes upon request for switches! I can also make the blank panel have holes wherever desired upon request.
I have set up a pole to help get me some feedback on potential interest. (VOTE ABOVE^^^)
Thanks guys
These panels are extremely thick and durable (still sit about .025" below the surface of the center console like the OEM panels) The clips are MUCH stronger than the thin and fragile OEM ones. The design will clip into the OEM holes and be removable just as the OEM panels are.
The potential models are:
1. Classic Cup Holder
2. Cup holder with two switches
3. Centered Cup holder
4. Blank panel
5. RX7 Panel
6. Switch blank
I will also be making the switch blank with custom sized holes upon request for switches! I can also make the blank panel have holes wherever desired upon request.
I have set up a pole to help get me some feedback on potential interest. (VOTE ABOVE^^^)
Thanks guys
Last edited by FCJG15; 01-13-15 at 09:42 AM.
#4
B O R I C U A
iTrader: (14)
Howdy guys and gals, as a new forum vendor, it is a great opportunity to now show off the panels I have been designing. I am currently awaiting what I genuinely believe will be my best and final prototype. These will hopefully be for sale in late January to early February. I am looking to see who would be interested and what your thoughts are!
These panels are extremely thick and durable (still sit about .025" below the surface of the center console like the OEM panels) The clips are MUCH stronger than the thin and fragile OEM ones. The design will clip into the OEM holes and be removable just as the OEM panels are.
The potential models are:
1. Classic Cup Holder
2. Cup holder with two switches
3. Centered Cup holder
4. Blank panel
5. RX7 Panel
6. Switch blank
I will also be making the switch blank with custom sized holes upon request for switches! I can also make the blank panel have holes wherever desired upon request.
I have set up a pole to help get me some feedback on potential interest. (VOTE ABOVE^^^)
Thanks guys
These panels are extremely thick and durable (still sit about .025" below the surface of the center console like the OEM panels) The clips are MUCH stronger than the thin and fragile OEM ones. The design will clip into the OEM holes and be removable just as the OEM panels are.
The potential models are:
1. Classic Cup Holder
2. Cup holder with two switches
3. Centered Cup holder
4. Blank panel
5. RX7 Panel
6. Switch blank
I will also be making the switch blank with custom sized holes upon request for switches! I can also make the blank panel have holes wherever desired upon request.
I have set up a pole to help get me some feedback on potential interest. (VOTE ABOVE^^^)
Thanks guys
Not mentioned, but what I would really like is one with the power mirror switch AND a hole/space for the master (driver) power window switch.
Trending Topics
#11
Selling off a prototype.
Photos are attached.
LIMITED OFFER ONLY 1 exists
100$ shipped because it comes with the switches.
I epoxied the fog switch in because the hole was a bit small and then my clips broke.
Will come with some foam tape to put around the inside lip to prevent movement (this panel was a bit shorter on the lengths than it should have been. Even with the foam it is BARELY visible.
These are getting closer and closer to being completed. This will fund future prototypes and parts!
Fits like a glove when the foam tape is in place!
Photos are attached.
LIMITED OFFER ONLY 1 exists
100$ shipped because it comes with the switches.
I epoxied the fog switch in because the hole was a bit small and then my clips broke.
Will come with some foam tape to put around the inside lip to prevent movement (this panel was a bit shorter on the lengths than it should have been. Even with the foam it is BARELY visible.
These are getting closer and closer to being completed. This will fund future prototypes and parts!
Fits like a glove when the foam tape is in place!
#12
Price drop to 85$ shipped. Trying to buy another prototype because there was a small gap still before I put these out to you guys for sale, if this panel doesn't go to one of you guys, it'll end up in my car. But I would love to see it in someone else's car with some photos and feedback!
#17
Limited time to buy.
Due to bills I may need to step away from the forum once vendor license is up 1 week from today.
If one of you guys gets me 75$ on this panel I'll be able to buy another month!
Testing prints on a new machine this weekend hopefully. If the prints are in good quality, the pricing of these panels may nearly half themselves! Hoping this plan works out.
Thank you guys for all of your interest and feedback!
Due to bills I may need to step away from the forum once vendor license is up 1 week from today.
If one of you guys gets me 75$ on this panel I'll be able to buy another month!
Testing prints on a new machine this weekend hopefully. If the prints are in good quality, the pricing of these panels may nearly half themselves! Hoping this plan works out.
Thank you guys for all of your interest and feedback!
#18
Banned. I got OWNED!!!
iTrader: (4)
Looks great! People always ask for a cup holder and I'm not sure to take them serious or not lol. Nice job stepping up to the plate, I'm sure you'll sell a few once it reaches more views. try posting in the Facebook groups.. a lot of lurkers there, not so much on the forums anymore..
#21
dont kill the cones
I think this really is a Fantastic idea, the worst part about early JDM cars is no cup holders!! I would definitely buy one, but my can needs to be road worthy first. Just thought you would want to hear input from a random. I think that $75-80 price range is right on, even for us "cheap" FC owners .
#24
PANAMAniac Rotor Head
Join Date: Mar 2004
Location: ORLANDO FLORIDA
Posts: 121
Likes: 0
Received 0 Likes
on
0 Posts