Power FC Stock Map for 850cc/1600cc single turbo !need help!
#1
Junior Member
Thread Starter
Join Date: Jul 2016
Location: Germany
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
Stock Map for 850cc/1600cc single turbo !need help!
Hello guys!
I need a stock map where my engine leaving. I look into the power fc program and... understand nothing Now i need a stock map where runs with my setup. Or a very good setup where i have more power and i can drive a month or something. So i can read more about power fc and perfect tune on a dyno..I hope someone can help me with stock map or a little bit better stock map where i have a little bit fun before i can go on a dyno.
That's my setup:
Power FC Datalogit
Gt3582r
Bosch 044 fuel pump
850cc/1600cc fuel injectors
Afm Fuel Rail
Afm Fuel pressure regulator
Greddy FMIC
Greddy elbow
No emission controls
Downpipe without catalyst, straight pipe 3"
Fuel pressure press on which psi? 43psi? Or more?
Thank you guys!
I hope anyone can help me
I need a stock map where my engine leaving. I look into the power fc program and... understand nothing Now i need a stock map where runs with my setup. Or a very good setup where i have more power and i can drive a month or something. So i can read more about power fc and perfect tune on a dyno..I hope someone can help me with stock map or a little bit better stock map where i have a little bit fun before i can go on a dyno.
That's my setup:
Power FC Datalogit
Gt3582r
Bosch 044 fuel pump
850cc/1600cc fuel injectors
Afm Fuel Rail
Afm Fuel pressure regulator
Greddy FMIC
Greddy elbow
No emission controls
Downpipe without catalyst, straight pipe 3"
Fuel pressure press on which psi? 43psi? Or more?
Thank you guys!
I hope anyone can help me
Last edited by NicNo1; 08-31-16 at 12:09 AM.
Trending Topics
#8
Eye In The Sky
iTrader: (2)
Join Date: Feb 2001
Location: In A Disfunctional World
Posts: 7,892
Likes: 0
Received 114 Likes
on
66 Posts
All you need to do is translate the 3 bar to 2 bar for the Settings 3 Map Ref table.
I had to do that when going from my stock 2 bar scale/offset to after I calibrated it for accuracy.
If you ever really paid attention to the PFC shown and logged boost values, you would see that they do not match your boost gauge. The PFC comes with inaccurate scale/offsets.
Most people are lazy and do not care. They just tune for the boost that they run even if the calculated P,N are not true for the boost.
The max boost that the stock map sensor can read is 17.56 psi but the PFC logs and shows
16.3 psi, that is 1.26 psi low.
I will admit that at lower boosts it is not so bad, at a true 10 psi, it is low by .94 psi.
#14
Rotary Enthusiast
BW s366
synapse wastegate, spring pressure
550/1600 rx7 store fuel kit
supra fuel pump
stock ignition
Stock Map sensor
You can't upload a .Dat file on here so i converted it to .txt
You might be able to convert it back to a .dat but I am not 100% sure on that...
Do more searching on here for the 850 primary settings .
synapse wastegate, spring pressure
550/1600 rx7 store fuel kit
supra fuel pump
stock ignition
Stock Map sensor
You can't upload a .Dat file on here so i converted it to .txt
You might be able to convert it back to a .dat but I am not 100% sure on that...
Do more searching on here for the 850 primary settings .
Thread
Thread Starter
Forum
Replies
Last Post
Rx7aholic
Engine Management Forum
3
03-07-01 11:35 AM