Power FC Datalogit/Wideband help
07-18-14, 09:16 PM
#1
Senior Member
Thread Starter
iTrader: (5)
Join Date: Dec 2011
Location: iowa city
Posts: 312
Likes: 0
Received 0 Likes
on
0 Posts
Datalogit/Wideband help
i got no readings on my datalogit from the wideband. i got voltage readings on the wires from the gauge but nothing on fc-edit on my laptop all i get are 0's. any thoughts>?
07-18-14, 10:21 PM
#2
07-19-14, 02:20 PM
#6
Senior Member
Thread Starter
iTrader: (5)
Join Date: Dec 2011
Location: iowa city
Posts: 312
Likes: 0
Received 0 Likes
on
0 Posts
So I have a 30-4100 aem uego, it's wired with the white cable on AN1 and the black cable I grounded and connected to AN2. The settings I put on the auxiliary are 6.6 and13.2AFR for afr.
07-19-14, 02:24 PM
#7
Rotary Enthusiast
iTrader: (19)
Join Date: Apr 2002
Location: Colorado Springs, CO
Posts: 1,169
Likes: 0
Received 11 Likes
on
10 Posts
When tuning some other cars, think the values were 10 and 20 afr. Look at manual to double check. Ensure values on w/b match or are very close to wide band readings.
Trending Topics
07-19-14, 02:36 PM
#8
Senior Member
Thread Starter
iTrader: (5)
Join Date: Dec 2011
Location: iowa city
Posts: 312
Likes: 0
Received 0 Likes
on
0 Posts
So the values I used were 10-20 and I was getting 0s on the map so today I'll be trying the 6-13 values I spoke of since that's what aem specifies for e85
08-07-14, 04:02 PM
#15
Senior Member
Thread Starter
iTrader: (5)
Join Date: Dec 2011
Location: iowa city
Posts: 312
Likes: 0
Received 0 Likes
on
0 Posts
this is what i found APEXi 415-A013 Power FC Boost Controller Kit Add-on
and i think maybe through the outputs on the datalogit you might be able to as well
and i think maybe through the outputs on the datalogit you might be able to as well
08-22-14, 06:30 AM
#16
Senior Member
Innovate made a quite good manual for their sensor and how to use it with Datalogit on a RX7 an finally use it to tune :-) . I know you got a AEM , but i thought most of it is generic in any way
LC-1 Integration into Apex Power FC w/Dataloggit Logger:: Innovate Motorsports Application Notes
LC-1 Integration into Apex Power FC w/Dataloggit Logger:: Innovate Motorsports Application Notes
09-07-14, 10:22 AM
#17
go to this link there is a PDF on aem widband setup with power fc
http://nyrotorsports.com/
there is a problem with AEM tho you probably wont get gauge and datalogit to read the same...
datalogit was more accurate then the gauge to .1 with lc-1 on the dyno
http://nyrotorsports.com/
there is a problem with AEM tho you probably wont get gauge and datalogit to read the same...
datalogit was more accurate then the gauge to .1 with lc-1 on the dyno
11-20-14, 04:58 PM
#18
Full Member
iTrader: (26)
Join Date: Mar 2012
Location: Savannah, GA
Posts: 103
Likes: 0
Received 0 Likes
on
0 Posts
Innovate made a quite good manual for their sensor and how to use it with Datalogit on a RX7 an finally use it to tune :-) . I know you got a AEM , but i thought most of it is generic in any way
LC-1 Integration into Apex Power FC w/Dataloggit Logger:: Innovate Motorsports Application Notes
LC-1 Integration into Apex Power FC w/Dataloggit Logger:: Innovate Motorsports Application Notes
Thread
Thread Starter
Forum
Replies
Last Post