Power FC AUX Input questions
01-25-16, 04:47 PM
#1
Full Member
Thread Starter
Join Date: Oct 2011
Location: Wilmington, NC
Posts: 220
Likes: 0
Received 0 Likes
on
0 Posts
AUX Input questions
I have an oil temp and fuel pressure gauge (both 0-5v gauges) connected to the aux inputs on the dataloggit. I am outputting the info using Raspexi.
They work but the inputs beside the where the wires are connected have voltage. does the 0v input on the dataloggit need a ground?
I know that the instructions for connecting a wide band say to connect a ground and subtract the value. I connected a ground that but it varies a lot making the numbers change erratically.
Who else has connected AUX input gauges and what did you do?
I believe the fuel pressure reads off because the floating ground.
They work but the inputs beside the where the wires are connected have voltage. does the 0v input on the dataloggit need a ground?
I know that the instructions for connecting a wide band say to connect a ground and subtract the value. I connected a ground that but it varies a lot making the numbers change erratically.
Who else has connected AUX input gauges and what did you do?
I believe the fuel pressure reads off because the floating ground.
02-03-16, 03:46 PM
#2
Eye In The Sky
iTrader: (2)
Join Date: Feb 2001
Location: In A Disfunctional World
Posts: 7,892
Likes: 0
Received 113 Likes
on
66 Posts
The way I set up my DL to remove floating ground problems is as follows:
(1) Installed an external wire connected to the DL internal ground.
(2) for each input source: run the sensor ground to the DL external ground, run the 0-5VDC to one of the DL inputs, put a noise filtering capacitor across the two inputs for the source.
Solves all the problems.
(1) Installed an external wire connected to the DL internal ground.
(2) for each input source: run the sensor ground to the DL external ground, run the 0-5VDC to one of the DL inputs, put a noise filtering capacitor across the two inputs for the source.
Solves all the problems.
02-05-16, 02:34 PM
#4
Full Member
Thread Starter
Join Date: Oct 2011
Location: Wilmington, NC
Posts: 220
Likes: 0
Received 0 Likes
on
0 Posts
The way I set up my DL to remove floating ground problems is as follows:
(1) Installed an external wire connected to the DL internal ground.
(2) for each input source: run the sensor ground to the DL external ground, run the 0-5VDC to one of the DL inputs, put a noise filtering capacitor across the two inputs for the source.
Solves all the problems.
(1) Installed an external wire connected to the DL internal ground.
(2) for each input source: run the sensor ground to the DL external ground, run the 0-5VDC to one of the DL inputs, put a noise filtering capacitor across the two inputs for the source.
Solves all the problems.
Where is DL internal ground? The 0V slot? What size capacitor? Sorry
02-10-16, 05:07 PM
#5
Eye In The Sky
iTrader: (2)
Join Date: Feb 2001
Location: In A Disfunctional World
Posts: 7,892
Likes: 0
Received 113 Likes
on
66 Posts
Usually the most common and largest runner on the circuit board is ground, but the safe way is to test with a ohm meter across the car chassis ground for smallest resistance. Also look for a black wire from the cable between the DL and PFC as it should also be ground and go to the ground of the DL.
As for the capacitor, contact the makers of the DL or O2 wideband makers.
As for the capacitor, contact the makers of the DL or O2 wideband makers.
Thread
Thread Starter
Forum
Replies
Last Post
