New Member RX-7 Technical Post your first technical questions here, in an easy flame free environment, before jumping into the main technical sections.

FD3S Smokey Cold Start

Thread Tools
 
Search this Thread
 
Old 12-04-13, 12:52 AM
  #1  
Junior Member
Thread Starter
 
BanzaiBoogie's Avatar
 
Join Date: Nov 2013
Location: Seattle WA
Posts: 15
Likes: 0
Received 0 Likes on 0 Posts
FD3S Smokey Cold Start

i recently bought an FD, morning starts the car tends to smoke a lot for a minute or so and then the smoke disappears, is this something I'm suppose to worry about? I've been told its probably just condensation, I'm just afraid one of the seals might be done but the car runs strong, doesn't seem like theres any problem after its warmed up. anytime its started it doesn't smoke at all.

i have read a couple other forum posts for this subject just couldn't find what i was looking for. Thanks.
Old 12-22-13, 11:47 AM
  #2  
Can Post Only in New Member Section
 
R0ckweld's Avatar
 
Join Date: Nov 2013
Location: Pennsauken, NJ
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
My FD also does the white smoke on cold starts, the colder it is the worse it is. And ive also heard its no big deal as long as it goes away once its warmed up a little.
Old 12-27-13, 09:29 AM
  #3  
GT35R

iTrader: (5)
 
atoro91's Avatar
 
Join Date: Oct 2013
Location: Atlanta, Ga
Posts: 20
Likes: 0
Received 0 Likes on 0 Posts
If the smoke only lasts a couple seconds it's probably just condensation. If it smokes a lot for close to a minute there is a good chance you have a bad coolant seal. Mine smoked a good bit for about 30 seconds after the car had sat for a day or two. When I got the engine apart, coolant poured out of the front housing. Hopefully you don't have a bad seal, but if it is you will have to do a rebuild.
Old 12-28-13, 11:25 AM
  #4  
GT35R

iTrader: (5)
 
atoro91's Avatar
 
Join Date: Oct 2013
Location: Atlanta, Ga
Posts: 20
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by db71
What about white smoke (almost looks like condensation) when letting of after a hard pull? Goes away quick but not very comforting to see. I havent gotten the car yet jusg trying to learn a little before jumping into it.
White smoke is definitely caused by water but I'm not sure that a little after a hard pull is due to a bad coolant seal. These engines do burn a little oil as part of their design so what you could be seeing may just be oil not water. Really all I have to go by is what I experienced with my car. There would be a big cloud of white smoke when I would start it after the car had sat for a day or two. After that burned off I wouldn't really notice it again.
Old 12-28-13, 06:15 PM
  #5  
Rotary
iTrader: (1)
 
Senna88's Avatar
 
Join Date: Dec 2013
Location: Montréal, Québec
Posts: 7
Likes: 0
Received 0 Likes on 0 Posts
Had the same problem.. but it's all good when the car warms up
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Kyo
2nd Generation Specific (1986-1992)
6
04-13-19 09:24 AM
stickmantijuana
Microtech
30
04-23-16 06:37 PM
1993fd3sracer1
3rd Generation Specific (1993-2002)
29
10-13-15 01:57 PM
1993fd3sracer1
1st Generation Specific (1979-1985)
20
09-07-15 11:50 AM
85TIIDEVIL
2nd Generation Specific (1986-1992)
7
08-25-15 12:09 AM



Quick Reply: FD3S Smokey Cold Start



All times are GMT -5. The time now is 01:35 PM.