BlinD26

iTrader: (27)

Has anyone tried a Corbeau Sportline RRS seat?

Here are the dimensions:

FD7KiD

iTrader: (8)

^^^ that seat looks gorgeous.

BlinD26

iTrader: (27)

Yeah they are pretty similar to the RX8 R3 Recaros and I haven't seen anyone run them yet.

Mahjik

iTrader: (1)

Compare the dimensions to the CR1's and Sparco Evo 2. The Sparco's rub the door and need some trimming and the CR1's fit without modifications. If the dimensions are within the same parameters at those two seats, then it should fit. At some point, someone has to be the first.

BlinD26

iTrader: (27)

That's the plan. I took a gamble and got Evolution X seats based on rought measurements, but that didn't pan out.

The seat backs are perfect (don't hit the doors) but the base is just too long/wide at parts to make it realistic to put in an FD.

Once I sell the Evolution X seats I have (baring finding a set of R3 Recaros) I think I'm going to give the Sportline RRS seats a shot.

X.ProphetEzra.X

iTrader: (1)

Are Atomic Rex style rails still available anywhere, I really like the way your seating position turned out.

gio64

iTrader: (1)

I have read through this thread and pulled up sizes for a bunch of these seats. I am a bit perplexed: unless I have mixed some dimensions and seats up, I found seats on the "fit" list that are bigger (top or bottom) than some of the seats in the "don't fit" list. Maybe I should gather all these dimensions up and post them here?

I would like to see somebody post the stock seats size (maximum bottom and top width) as well as the distance from the centreline of the seat to the door panel.

If you wonder why I'm not measuring it myself, my car is being taken care of, so it is not within my reach.

sypath

iTrader: (1)

How about sparco pro2000?

speedjunkie

iTrader: (3)

I'm eager to see if this one will fit. I haven't found a spec sheet on it with dimensions, but I emailed Sparco and I'm waiting to hear back.

Sparco USA

Comparing between it and the EVO II, I'm thinking it won't fit without even more modification than the EVO II. There is more space between the harness holes, and they are also wider than on the EVO, and it looks like the width from the edge of the harness hole to the furthest point on the wing might be the same size, maybe a tad shorter than on the EVO.

I've been planning on getting the EVO II but I'm not crazy about cutting up a brand new seat. I've been looking at the Suzuka Pro GT since it fits a little better and I like how the leg bolsters come up higher at the edge.

JBF

iTrader: (13)

Something I've learned in my trials and tribulations of trying to fit my 6'1" 34" waist frame into any type of seat (made to fit smaller cars such as the FD) that will get you lower in to the car is physically impossible.

The wider based seats won't clear the stock rail mounting positions and will in turn, position you higher than the stock seats.

The only logical way to fit "normal" sized Americans in to a bucket, AND be sitting lower in the car, is to have some custom mounts made. There's no other way. I have been through three types of seat and mount configurations to no avail. Being that I have a roll cage, I had to go more in depth and cut out the rear stock mounting "pads" and reinforce the chassis pan. Then I had some mounts welded straight to the floor.

If you're getting buckets merely for aesthetic reasons, save your money and get the JDM Recaros. That's really the only way to go without doing something relatively custom.

Again, this is my $.02 considering my body frame and what I've already been through.

speedjunkie

iTrader: (3)

^Was that a response to me or in general?

If I had a choice, I'd get seats that recline still, something like the Bride Gais, so I can get into my rear bins still. However, I'm not paying that crazy amount of money for a seat that's not even FIA approved. Also, I already got a set of mounts from Adam Griffith that mount directly to the floor and only fit side mount bucket seats. I'm 6'3" and I sat in his EVO II with the same mounts and had extra space for a helmet. I'm just not crazy about having to trim off so much of a brand new seat, and I like a couple things about the Suzuka Pro GT and I really like that new Grid, I'm just not sure yet if it'll fit.

Also, I'm not sure getting the JDM Recaros should be considered "saving money" when they cost more than most of the bucket seats out there lol.

JBF

iTrader: (13)

It was just in general. I have taco neck with a helmet on in my pro2000 and Adam's mounts. Headliner and sunroof is completely removed. That gives me space directly above my head, but my front down bar for the roll cage gets in the way.

speedjunkie

iTrader: (3)

Uh oh, if you're 6'1" and have a problem fitting with pretty much the same parts I'm going to have, I hope I have a shorter torso or something lol. I have a sunroof also. I don't have a roll cage though, just gonna be using the roll bar, so hopefully that will help some.

mannykiller

iTrader: (93)

Very nice!!! Cobra has a few nice options! Solid seats...some are FIA and I think this one is as well. Definitely on my list of seats to seriously consider

speedjunkie

iTrader: (3)

Anyone else have the Suzuka Pro or Pro GT seats and can comment on how comfortable they are or aren't? Specifically for longer trips.

speedjunkie

iTrader: (3)

I'm curious about some of these seats fitting and others not fitting. If you look at this site...

http://www.safedrives.com/prodimages...cingShells.pdf

...the Pole Position is not as wide as the Profi SPG at the shoulder bolsters, but wider at the bottom. Also, are the seats measured with the foam or without? It might not hurt for everyone to say what seat rails they are using when the seat fits. I've seen some mention using rails from a different manufacturer than the seat to help them fit. And I know some have said, but some haven't. It also might help if people list where the seat had to be modified...just the shoulder bolsters and/or the side bolsters so it doesn't touch the door panel and/or tranny tunnel.

I'm 6'3", about 220lbs. My waist measures around 38" but my hips seem to be around 44", and when I sit down, they're about 16" across which comes out to 406mm. If a seat is measured with the foam, I should be able to fit into the regular Recaro Profi SPG and don't need to step up to the XL.

I bought rails from Adam Griffith to bolt the seat directly to the floor, and he has the EVO II with the same rails. I sat in it and fit and it seemed like I'd have enough headroom, but I'm wondering if I can find a seat that I won't have to modify quite as much. Such a pain trying to find a seat to fit our cars, but I guess it's not as bad as a Miata or an S2000 lol.

speedjunkie

iTrader: (3)

Oooh la la!

Cobra Nogaro Seat | Fast Car Magazine

I'm gonna message them and see if I can get some specs on this seat.

EDIT: Damn, I just realized these don't have the lap belt holes, and probably not for 5/6pt harnesses either.

JBF

iTrader: (13)

A lot of the seats WILL fit with combinations of rails and mounts for normal driving purposes. However, if you plan on doing track days that require wearing a helmet, you're going to have a lot of trouble.

Using only a 4 point roll bar would definitely save you some head room vs a 6 point.

There are other ways around it, but that would also require reclining the seat so far back that it would not be a comfortable (or safe) driving position.

speedjunkie

iTrader: (3)

Yeah that's the whole point of getting a different seat, to lower it all the way to the floor so I can fit with a helmet. I plan on trying different degrees of tilt to get the lean and angle of the legs where I want them. Not too extreme, just a little if possible.

I hadn't even planned on getting a roll bar until I saw Westley selling his haha. I've had the harness bar for years now and planned on getting the different ends to use the roll bar but then I heard he had stopped making them.

I got an email back from a Sube Sports rep about the Cobra Nogaro. It looks like that seat would fit easily in our cars.

wthx100

Seat Dimensions

Backrest Height: 918 mm (36.1 inches)
Shoulder Width: 517 mm (20.4 inches)
Seat Width: 511 mm (20.1 inches)
Seat Cushion Depth: 483 mm (19.0 inches)
Gross Weight: 33.1 lbs.
Belt: 3-point

fastfalcon94

iTrader: (3)

I have the corbeau RRS seats in my 3000gt vr4. I like everything about them except they are a little narrow in the shoulder area. I am hoping that someday they will make a wide version. The stock corbeau brackets also are pretty high so I made my own to lower them. MaximalPerformance.com gave me the best price I could find.




corbeau bracket on the left, my bracket on the right

jase03

I'm looking to put the Corbeau RRS seats in my FD.

Do you think they will fit ?

Cheers
Jase

Korican_boy

Anybody tried Sparco R100 seats in their FD?

Jacobframe

just wondering has anyone tried fitting sparco 2000 pros? im 6ft4 200 pounds with a jdm model fd3s, needing to get some more room..

airjordan223

iTrader: (8)

Based on their dimension on the website, I'd say it probably wont fit without cutting the seat similar to the evo.