Haltech Need help E11 ignition info. for 13B
#1
Need help E11 ignition info. for 13B
Hi guys,
I need some wiring info. for hooking up the Ignition System for 13B operation, with respect to the Ignition Toggle, for using the Stock S4/5 Coils w/ignitors. From the Instruction manual for the Primary 34 Pin jack, it says that IGN3 (Pin #5, Yellow/Orange) is used for the Toggle function. But where exactly does this hook up to the Trailing Ignitor?
Thanks
spanner
I need some wiring info. for hooking up the Ignition System for 13B operation, with respect to the Ignition Toggle, for using the Stock S4/5 Coils w/ignitors. From the Instruction manual for the Primary 34 Pin jack, it says that IGN3 (Pin #5, Yellow/Orange) is used for the Toggle function. But where exactly does this hook up to the Trailing Ignitor?
Thanks
spanner
#2
Originally Posted by spanner
Hi guys,
I need some wiring info. for hooking up the Ignition System for 13B operation, with respect to the Ignition Toggle, for using the Stock S4/5 Coils w/ignitors. From the Instruction manual for the Primary 34 Pin jack, it says that IGN3 (Pin #5, Yellow/Orange) is used for the Toggle function. But where exactly does this hook up to the Trailing Ignitor?
Thanks
spanner
I need some wiring info. for hooking up the Ignition System for 13B operation, with respect to the Ignition Toggle, for using the Stock S4/5 Coils w/ignitors. From the Instruction manual for the Primary 34 Pin jack, it says that IGN3 (Pin #5, Yellow/Orange) is used for the Toggle function. But where exactly does this hook up to the Trailing Ignitor?
Thanks
spanner
PIN 3....... Yellow/Black......Leading.... Green/Yellow
PIN 4....... Yellow/Red........Trailing...... Blue/Yelllow
PIN 5....... Yellow/Orange..Toggle....... Brown/Yellow
#3
E11 info
Originally Posted by crispeed
E-11 ECU....Haltech.................................Maz da
PIN 3....... Yellow/Black......Leading.... Green/Yellow
PIN 4....... Yellow/Red........Trailing...... Blue/Yelllow
PIN 5....... Yellow/Orange..Toggle....... Brown/Yellow
PIN 3....... Yellow/Black......Leading.... Green/Yellow
PIN 4....... Yellow/Red........Trailing...... Blue/Yelllow
PIN 5....... Yellow/Orange..Toggle....... Brown/Yellow
Thanks a million dude, would be really nice for yuh to make a lil pass back in T&T sometime !! I'll send yuh a couple pics of my present project.
Laterz
#4
Ok, the motor started up , but I find that the trigger angle had to be set to around 30 for the leading mark to line up with the pointer. I set the CAS with tooth offset of 3, as HItman's settings. Is this correct, or do I need to set over the CAS , in order to get a value closer to 65 +/- ?
#7
E11 Ign
Hi Crispeed,,,,, would these apply if I were to use individual MSD coils
with DIS units??
or would you know which E11 outputs go to which plug,like IGN 1 to leading 1,IGN 2 to trailing 1 leading2 etc,etc.
I want to replace my microtech with the E11 but I have been trying to find
the ignition diagrams for my Turbo II,,, I am currently using 2 MSD DIS2,and 4 coils,,,,,
with the microtech diagram I could see which wire goes to where, but I find it
difficult for the haltech,because there is no specific diagram that I can follow.
I am using 10 injectors staged, I figured that part already but I need some help
on the IGN side. thanks in advance.......
I searched the forum and the web but had no luck,Ive also emailed haltech,,,
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
ncds_fc
2nd Generation Specific (1986-1992)
19
09-15-15 12:03 AM