Haltech E11 2 step/aux rev limit settings
#1
E11 2 step/aux rev limit settings
What should the settings be for the 2 step on the E11?
HOW hard is a two step on the motor. IIRC i read that it puts a lot of strain on the corner seals but exactly how much. If not abused would the stock corner seals take it for a while, maybe a season? Or would i be better off using the anti lag instead?
TIA
Allen
HOW hard is a two step on the motor. IIRC i read that it puts a lot of strain on the corner seals but exactly how much. If not abused would the stock corner seals take it for a while, maybe a season? Or would i be better off using the anti lag instead?
TIA
Allen
#2
EFI Tech Wannabe
iTrader: (1)
Join Date: Sep 2003
Location: D.R., USA, the world...
Posts: 2,405
Likes: 0
Received 4 Likes
on
4 Posts
Originally Posted by 13B-RX3
What should the settings be for the 2 step on the E11?
HOW hard is a two step on the motor. IIRC i read that it puts a lot of strain on the corner seals but exactly how much. If not abused would the stock corner seals take it for a while, maybe a season? Or would i be better off using the anti lag instead?
TIA
Allen
HOW hard is a two step on the motor. IIRC i read that it puts a lot of strain on the corner seals but exactly how much. If not abused would the stock corner seals take it for a while, maybe a season? Or would i be better off using the anti lag instead?
TIA
Allen
There's also the Aux. RPM Limit, which is just that, when enabled, puts the engine at a different setpoint than the normal rev limiter, doesnt make as much boost as anti-lag, and basically just shuts off and turns back on the injectors at the set RPM, making loud bang bang bangs when it hits.
If the "2 step" is either one of these functions, i say use antilag, since you have several parameters to control and make it work good, adding additional fuel is one of them.
Also, you should never stay on the feature for too long anyway, just learn to work with it, and just try to coordinate your self to put your foot down 2 or 3 seconds before the light goes green and that way you'll strain the motor less.
#3
I know how the aux rev limit and anti lag work i just don't know how to set them up. For the aux rev limit there are two settings "hard" and "soft" I would assume for the aux rev limit you would set it to soft. But there are 4 other sub categories "linear soft cut" "hard to soft cut" "soft to hard cut" and "custom soft cut". I don't know which one to chose. For the record the aux rev limit "2 step" cuts ignition not fuel.
If i use th anti lag what should i set the % enrich and ign retard to?
Thanks for your time Claudio
If i use th anti lag what should i set the % enrich and ign retard to?
Thanks for your time Claudio
#4
EFI Tech Wannabe
iTrader: (1)
Join Date: Sep 2003
Location: D.R., USA, the world...
Posts: 2,405
Likes: 0
Received 4 Likes
on
4 Posts
I would start with the base parameters Haltech has put in there, if you feel that its way to ruch or you're fearful for the life of your motor with the timing retard value thats in there, start lower, and see how much boost you make on it, under the default settings, then try changing those 2 values as you see fit. Also, i would not spend an hour trying to figure it out, 4-5 attempts at a time is what i would try.
Let me know how it goes.
Let me know how it goes.
Trending Topics
#8
EFI Tech Wannabe
iTrader: (1)
Join Date: Sep 2003
Location: D.R., USA, the world...
Posts: 2,405
Likes: 0
Received 4 Likes
on
4 Posts
Originally Posted by 13B-RX3
I am using a Digital 6 for the leading and a DIS 4 for the trailing.
#12
I don't know if either MSD has a dual rev limit. Are you saying to just launch the car at whatever the redline is and forget the "2" step. Would that cause a problem with the trailing possibly firing before the leading or am i just reading too deep. Just whisper it, i promise i wont tell.
Thanks
Thanks
Last edited by 13B-RX3; 04-02-07 at 08:54 PM.
#14
Soooo i decided to actually read ALL the instructions on the DIS-4/Digital-6 and guess what. They both have built in 2-steps. Damn Chris, stop making me ask these stupid questions!!!
But seriously, thanks. My windshield will be in this week so it shouldn't be long before i get a few passes in her.
But seriously, thanks. My windshield will be in this week so it shouldn't be long before i get a few passes in her.
#15
Originally Posted by 13B-RX3
Damn Chris, stop making me ask these stupid questions!!!
BTW. There's no such thing as a dumb question. Dumb answers yes!
The dumb thing is to try it without asking first.
Last edited by crispeed; 04-10-07 at 11:57 PM.
Thread
Thread Starter
Forum
Replies
Last Post
rx8volks
Canadian Forum
0
08-13-15 04:55 AM