raceratheart15

iTrader: (1)

Figured the year round warm weather deprived car enthusiasts have plans for their cars this winter and might wanna share!

Me, i dont even have a RX7 anymore However I am turboing my daily dirver Mazda Protege5 using the parts off of a 03.5 Mazdaspeed Protege. I plan to just do the swap of all the handling and go fast goodies with a couple extras such as a properly plumbed intake, a FMIC, a wideband, stickier tires on the Racing Harts and maybe a few odds and ends depending on my budget. Hope to be tracking and autocrossing the car in the spring once im through school the first thing im buying is a FD again just gotta make due with what I got
Here is my P5




What is the best bang for buck grippy street tire do ya'll think? 215/45/17 im going to start shopping soon

IAN

iTrader: (3)

-Install AEM IGN-1A coils and sequential ignition. Probable a waste of money as I already had a autronic 500R amplifier. Although this will be a cleaner simpliar install. Maybe.
-Install H20 kit. Pretty much there just need to install water inector into intercooler and tank. Controller and wiring already run
-Dream about new suspension. Thinking Ground Control coil overs.
-Clean the interior. Clean more of the interior. And clean more of the interior.
-Have Marco "Thewird" tune the adaptronic custom 440D, BNR stage 3 turbo to whatever she can push.Finally after years drive the car.
-make custom air dam for rad, oil cooler and brake ducts.

Buggy

iTrader: (8)

I need to get the engine for my Rx-4 rebuilt. It's already tore done. Just have to check all the parts, order seals, clean and paint, then reassemble. Sounds easy... lol

RXeckless

iTrader: (11)

Plans, nothing to due with any rotaries. FD bundled up for the winter, need lots of work but lately my heart is just not into it.
The List:
All rear bushings and reseat the whole suspension, getting a lot of knocks/clunks in the rear end.
Get down to Marco early spring for a proper tune.
Then drive the **** out of it till it F@#ks up again, and being a FD that won't be long!

JDK

iTrader: (8)

Nothin'.....just fixing the snow blower

23Racer

Way too much to list here, but I will give top line stuff.

RX7 - Build new lower front splitter for the RX7. Build a new cold air box as I have to get those socks off the trumpets. Change all lubes, reset front wheel bearings, put on new eccentric shaft pulley. RX7 Done.

Cougar#1 - Repair air inlet tube to correct for issues caused by over enthusiastic clamp tightening. Replace 60 mm TB with 75 mm TB. Get computer reflashed with new map if possible. If not swap in SDS or Megasquirt. get Quaife parts back from Joe, measure out all out of spec pieces and get new parts from Quaife. Build new dogbox and put in car. Cougar done.

Cougar #2 - find intermittent dodgy wiring issue, clean up car a ton, put new roof panel on car, set alignment properly, repair wonky rear brake disc issue, clean up appearance. Cougar #2 done.

Team - Prepare all bits and pieces for a couple Canadian Touring Car Championship events this year with the Cougar. Get ready for the 3 GT Superseries Events at TMP and SMP with both Cougars and the RX7. Potentially look at running 3 or 4 CASC GT Challenge races with all 3 cars if sponsorship comes through. If sponsorship comes through, then regraphic all 3 cars.

I'm certain there is more, but that's all I can think of right now. So basically nothing.

Eric

distr0

iTrader: (1)

-Swap transmission, new clutch, pp
-Relocate battery to rear bin
-HX35 turbo, manifold, downpipe, fmic, piping, injectors, fuel pump, etc etc etc

RevRx7

iTrader: (1)

- Engine rebuild with a large street port
- Get the car to Marco early spring for a new turbo setup & tune
- New Downpipe

there's other little things i want to do, but thats the main stuff that needs to be done.

thewird

iTrader: (8)

All I'm doing this winter is saving money for a sequential gearbox capable of holding the torque for the 20b. After that be broke again but at least the car will have what it needs. Tired of swapping transmissions more often then I change oil (I'm not even kidding lol). I'm working on everyone else's car so that will keep me occupied to not touch my car long enough to save for the gearbox lol.

thewird

HiWire

Reading the service manual and some of the other rotary material online.

Re-reading my books:
RX-7: Mazda's Rotary Sportscar by Brian Long
RX-7: Mazda's Legendary Sports Car by Jack K. Yamaguchi & John Dinkel
Mazda RX-7 Performance Handbook by Mike Ancas
Street Rotary by Mark Warner
Never Stop Challenging! by Pierre Dieudonne

Playing Gran Turismo 6, GTR2, and Need for Speed Shift 2 Unleashed

misterstyx69

iTrader: (142)

I'll be reading "How to be Debt Free in 90 days"...by Shuda Cudawoodah.

thewird

iTrader: (8)

Step 1: sell everything in your possession related to rotaries

Step 2: stop thinking about everything performance car related

Step 3: sell your girlfriend

Step 4: your done

thewird

rollcoal

iTrader: (5)

rebuild entire engine
street port
single turbo
aem ignition coils
install water meth
abs,ps,ac delete
upgrade fuel lines -8an feed -6 return
install fuel pump/fuel rails/injectors
body work and paint...looks like the car won't be running til mid summer aha
get marco to tune the car
do burnouts all day

misterstyx69

iTrader: (142)

Step 1&2....in the market???..bring a truck.

Step#3..how do you think I got a car?..(unless she can fix a transmission,I don't need extra baggage!)

..hmm..guess I'm done.

domrx7

iTrader: (7)

Reading everyone's list it seems like Marco will be extremely busy through the winter and spring...LOL.
I will be taking my Fd to the my body guy hopefully this weekend for a few front end changes.... and like almost all of you I need to get to Marco as well for minor tune and Dyno.

Prôdigy2nd

iTrader: (3)

Change from old turbo/fuel setup to new EFR 8374 IWG... And something different for fuel...

Maybe paint bay/door jams...

Do a bunch of small ****...

I am excited to install my newly acquired CDN rear washer tank as a WM resivour...

Cause .9L jdm tank lasts maybe a week if I'm really really nice on the car... lol


J.

85RotaryRocket

iTrader: (1)

just built my 2jz up(complete rebuild). installed new single turbo,manifold, exhaust, fuel system , aem v2, and about to start her up in a week or so. break in process / tuning begins. debating to keep my 4.3 diff or drop it to a 4.1. new rear subframe bushings about to go in. just got a q45 throttle body placed on my intake will polish up the manifold. welding up the new inter-cooler piping. debating to go to ls1 coils, might go 4 inch piping.

ill make a conservative 620/40 with 94 for now. get some e86 and go for 700+ and hope my tranny holds up . if not t56 mag or v160 and call it a day.

85RotaryRocket

iTrader: (1)

E85 lol it was late.

welfare

get this damn murano back together and running so i can get the 7 back in the garage and solve it's idle issue. maybe give it an adjustable fpr and install my koyo rad

DaoNhatHai

iTrader: (38)

Deciding if I want to do the whole
-American V8 thing with a 4th gen Mustang (not likely)
-Euro thing with either an E46 330CI ZHP or E39 540i M-Sport
...... or get back into the Rotary game in either an FC RX-7 or 1st gen RX-8

Aaron Cake

iTrader: (1)

Well after letting the RX-7 sit all year due to it being on half an engine, that itself caused by my own mistake of not replacing a suspected bad fuel injector, the engine was finally disassembled:


And went back together two weeks ago, which at some point will have a video when I get around to editing.

Still plugging away at the Cosmo front suspension. With all the interruptions and waiting for parts, I'm unhappy still working on it 4 months after I started.

splat_mat

iTrader: (3)

I'm just going to put this here....