Water Injection
#3
Penis Healthy
iTrader: (5)
Join Date: Jul 2013
Location: █▬█ █▄█ █▬█ █▄██▬█ █▄█ █▬█ █▄█
Posts: 2,595
Received 779 Likes
on
446 Posts
AEM is the best bang for the buck IMO. Comes with map switch and everything.
30-3300 is the 1 gallon reservoir kit.
https://www.google.com/webhp?sourcei...shop&q=30-3300
30-3300 is the 1 gallon reservoir kit.
https://www.google.com/webhp?sourcei...shop&q=30-3300
Trending Topics
#9
Urban Combat Vet
iTrader: (16)
https://www.rx7club.com/auxiliary-in...wi-kit-807016/
There's a debate on erosion of the turbo impellers with pre-turbo. Personally I think that stemmed from guys essentially just squirting water into the turbo and it's not an issue with a good nozzle, but full disclosure...I've never looked into it seriously. As far as Wannaspeed itself, I've heard nothing but positive.
And you DO know there's an AI section...right?
Ok, I'm looking at the AEM. Any opinions on the wannaspeed kit?
Mechanical Pre-Turbo Water Injection - Wannaspeed
Mechanical Pre-Turbo Water Injection - Wannaspeed
And you DO know there's an AI section...right?
Last edited by Sgtblue; 01-04-17 at 10:13 AM.
#10
B O R I C U A
iTrader: (14)
Ok, I'm looking at the AEM. Any opinions on the wannaspeed kit?
Mechanical Pre-Turbo Water Injection - Wannaspeed
Mechanical Pre-Turbo Water Injection - Wannaspeed
I have been using pre turbo water injection for almost 5 or 6 years now, and have not noticed any blade erosion, however I have not disassembled the front cover, nor inspected the compressor with a magnifying glass!
#11
Full Member
iTrader: (3)
Ok, I'm looking at the AEM. Any opinions on the wannaspeed kit?
Mechanical Pre-Turbo Water Injection - Wannaspeed
Mechanical Pre-Turbo Water Injection - Wannaspeed
#14
Long time on-looker
iTrader: (33)
Coolingmist trunk mount stage 1. Simple and effective. I used the initial version for about 5 years of hard use (track use where it runs A LOT), and the pump failed last year. I replaced it with the newer higher PSI pump and one of their new nozzles and have had good success so far.
#17
Urban Combat Vet
iTrader: (16)
^That is a good read, thanks. Echos a lot of what's in the AI section stickys...except that I would not use the formulas in those links for our rotary engines for nozzle sizing etc. And I've never had an issue with the old-tech diaphragm pump on my car over the 6 or 8 years I've had it. But I probably don't work it as hard as they do.
Last edited by Sgtblue; 01-22-17 at 09:27 AM.
#18
Instrument Of G0D.
iTrader: (1)
An interesting read on WI (for bikes, but still interesting)...
https://www.rbracing-rsr.com/waterinjection.html
https://www.rbracing-rsr.com/waterinjection.html
Was always tempted to do this but wasnt sure. Any body else use it? Its just easier to get hold of.
#19
Spanking Pcars
iTrader: (4)
Join Date: Aug 2004
Location: DFW area
Posts: 1,084
Likes: 0
Received 0 Likes
on
0 Posts
Coolingmist trunk mount stage 1. Simple and effective. I used the initial version for about 5 years of hard use (track use where it runs A LOT), and the pump failed last year. I replaced it with the newer higher PSI pump and one of their new nozzles and have had good success so far.
#20
I install a lot of AEM kits, very nice kits. For my own cars I inject boost juice.
We stock both AEM and Snow kits Water Injection
We stock both AEM and Snow kits Water Injection
#21
Racing Rotary Since 1983
iTrader: (6)
AEM re-engineered their AI product a few years ago and it is now a first rate/recommended unit.
i have also had excellent results from Coolingmist over the years and they have a wide product array and excellent website.
if you plan to run 100% meth i recommend Alkycontrol.
i have also had excellent results from Coolingmist over the years and they have a wide product array and excellent website.
if you plan to run 100% meth i recommend Alkycontrol.
Thread
Thread Starter
Forum
Replies
Last Post