used 850's, is this going to be ok...?
#1
Hi Powr FD's
Thread Starter
Join Date: Oct 2002
Location: OKC
Posts: 806
Likes: 0
Received 0 Likes
on
0 Posts
used 850's, is this going to be ok...?
I picked up some used 850's, but the plastic caps are partially broken off, around the area where the connector attaches. *the connector parts are good.
They will be going into my primary rail,
will this affect anything, especially when it comes to milling my primary rail to fit them?
Ill take pics if you need me to be more clear.
thanks
p.s. (double checking.. 850's are the long ones right? 550's are short?)
They will be going into my primary rail,
will this affect anything, especially when it comes to milling my primary rail to fit them?
Ill take pics if you need me to be more clear.
thanks
p.s. (double checking.. 850's are the long ones right? 550's are short?)
#3
Mr. Links
iTrader: (1)
Originally posted by GOOFYROTOR
wha wha what r u dalkin about? r u dalkin bout FD injectors onto FD fuel rail?
wha wha what r u dalkin about? r u dalkin bout FD injectors onto FD fuel rail?
HeatTreated,
The longer injectors are the primaries.
As far as the broken plastic, if it's on the top where the connection is, then it shouldn't be a problem, however a picture would help. You might think about sending them to RC Engineering before you install them for cleaning and flow balancing.
#4
cams pistons valves
Join Date: Jun 2003
Location: LA
Posts: 3,004
Likes: 0
Received 0 Likes
on
0 Posts
mahjik.........u shouldnt even be on this sight!!!!
longer shorter ....dont matter!!!
if u put sec onto pri , result is ,the IDLE low end response is going to be BAD.
WHO CARES IF THE PLUG FITS! this is NOT the point!
i dont think u know anything bout the technical side.
longer shorter ....dont matter!!!
if u put sec onto pri , result is ,the IDLE low end response is going to be BAD.
WHO CARES IF THE PLUG FITS! this is NOT the point!
i dont think u know anything bout the technical side.
#5
Hi Powr FD's
Thread Starter
Join Date: Oct 2002
Location: OKC
Posts: 806
Likes: 0
Received 0 Likes
on
0 Posts
thankx
See thats what I though.. I have the shorter injectors and they are fine, but after looking at the manual, I swear it shows the shorter ones going into the Secondary rail on the manifold (not into the engine)
The shorter ones are fine.
So looks like I dont need to worry about the long ones then
See thats what I though.. I have the shorter injectors and they are fine, but after looking at the manual, I swear it shows the shorter ones going into the Secondary rail on the manifold (not into the engine)
The shorter ones are fine.
So looks like I dont need to worry about the long ones then
Last edited by HeatTreated; 02-09-04 at 01:40 PM.
#6
Lives on the Forum
Join Date: Dec 2001
Location: San Lorenzo, California
Posts: 14,716
Likes: 0
Received 8 Likes
on
8 Posts
Originally posted by GOOFYROTOR
mahjik.........u shouldnt even be on this sight!!!!
longer shorter ....dont matter!!!
if u put sec onto pri , result is ,the IDLE low end response is going to be BAD.
WHO CARES IF THE PLUG FITS! this is NOT the point!
i dont think u know anything bout the technical side.
mahjik.........u shouldnt even be on this sight!!!!
longer shorter ....dont matter!!!
if u put sec onto pri , result is ,the IDLE low end response is going to be BAD.
WHO CARES IF THE PLUG FITS! this is NOT the point!
i dont think u know anything bout the technical side.
#7
Mr. Links
iTrader: (1)
Originally posted by GOOFYROTOR
mahjik.........u shouldnt even be on this sight!!!!
longer shorter ....dont matter!!!
if u put sec onto pri , result is ,the IDLE low end response is going to be BAD.
WHO CARES IF THE PLUG FITS! this is NOT the point!
i dont think u know anything bout the technical side.
mahjik.........u shouldnt even be on this sight!!!!
longer shorter ....dont matter!!!
if u put sec onto pri , result is ,the IDLE low end response is going to be BAD.
WHO CARES IF THE PLUG FITS! this is NOT the point!
i dont think u know anything bout the technical side.
2: He didn't ask "if the plug fits or not".
Did you even read his questions? No. The point is, he asked specific questions. None of which you answered or for that matter, understood.
Trending Topics
#8
Belligerent Security
Join Date: Jul 2003
Location: Pulling you over
Posts: 70
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by GOOFYROTOR
mahjik.........u shouldnt even be on this sight!!!!
longer shorter ....dont matter!!!
if u put sec onto pri , result is ,the IDLE low end response is going to be BAD.
WHO CARES IF THE PLUG FITS! this is NOT the point!
i dont think u know anything bout the technical side.
mahjik.........u shouldnt even be on this sight!!!!
longer shorter ....dont matter!!!
if u put sec onto pri , result is ,the IDLE low end response is going to be BAD.
WHO CARES IF THE PLUG FITS! this is NOT the point!
i dont think u know anything bout the technical side.
#9
cams pistons valves
Join Date: Jun 2003
Location: LA
Posts: 3,004
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Mahjik
1: He didn't ask about the idle when using 850's in the primary rail.
2: He didn't ask "if the plug fits or not".
Did you even read his questions? No. The point is, he asked specific questions. None of which you answered or for that matter, understood.
1: He didn't ask about the idle when using 850's in the primary rail.
2: He didn't ask "if the plug fits or not".
Did you even read his questions? No. The point is, he asked specific questions. None of which you answered or for that matter, understood.
u know what , i dont think your qualify to POST here.
im sick and tired of explaining everything.
sorry ,you're gonna have to learn this at school.
#11
Senior Member
iTrader: (3)
Join Date: Aug 2002
Location: Bay Area, CA
Posts: 435
Likes: 0
Received 0 Likes
on
0 Posts
you don't have to mill the primary to get them to fit. you can put the o-ring on in front of the plastic lip instead of behind it to compensate for its short length. Other people use an extra o-ring in the normal position that works also. Obviously you'll need a programable fuel controller (like the PowerFC) to controll the new setup.
#12
you don't have to mill the primary to get them to fit. you can put the o-ring on in front of the plastic lip instead of behind it to compensate for its short length. Other people use an extra o-ring in the normal position that works also.
Also do you know how well this works for a long time period? I'm just scared of spraying gas all over the place.
thanks
#13
Mr. Links
iTrader: (1)
Originally posted by GOOFYROTOR
what do u think a primary rail does? i thought so!
u know what , i dont think your qualify to POST here.
im sick and tired of explaining everything.
sorry ,you're gonna have to learn this at school.
what do u think a primary rail does? i thought so!
u know what , i dont think your qualify to POST here.
im sick and tired of explaining everything.
sorry ,you're gonna have to learn this at school.
Originally posted by rx7raca
Also do you know how well this works for a long time period? I'm just scared of spraying gas all over the place.
Also do you know how well this works for a long time period? I'm just scared of spraying gas all over the place.
#14
cams pistons valves
Join Date: Jun 2003
Location: LA
Posts: 3,004
Likes: 0
Received 0 Likes
on
0 Posts
[QUOTE]Originally posted by Mahjik
[B]Once again, you are just making up crap which has absolutely NOTHING to do with the original questions of this thread.
blah blah blah i guess u can write all u want here.
such a waste of time with a hardhead that writes his opinions
[B]Once again, you are just making up crap which has absolutely NOTHING to do with the original questions of this thread.
blah blah blah i guess u can write all u want here.
such a waste of time with a hardhead that writes his opinions