interesting gauge pod for miatas...
#1
interesting gauge pod for miatas...
i wonder of this will work with our FD's...
"This custom designed panel is specifically injection molded in black polycarbonate to fit your DIN (radio) slot (1997 to 2005 Miata) AND it will also fit some 1996 models (with #1273 radio). It is also rumored to be able to fit earlier cars by swapping out the console surround. It's finish will match the other items in your console exactly (radio, HVAC controls), and it snaps into place - no gluing necessary.
The panel comes standard with two 52.4 mm (2.062 inch) gauge openings. If you want a 3 hole panel, we will drill it for you. If you want to be able to install a BRB (Big Red start button from a Honda S-2000) we can drill the 1-1/4" hole for that as well. See examples in the photo."
http://www.thompson-automotive.com/c...11/2029659.htm
"This custom designed panel is specifically injection molded in black polycarbonate to fit your DIN (radio) slot (1997 to 2005 Miata) AND it will also fit some 1996 models (with #1273 radio). It is also rumored to be able to fit earlier cars by swapping out the console surround. It's finish will match the other items in your console exactly (radio, HVAC controls), and it snaps into place - no gluing necessary.
The panel comes standard with two 52.4 mm (2.062 inch) gauge openings. If you want a 3 hole panel, we will drill it for you. If you want to be able to install a BRB (Big Red start button from a Honda S-2000) we can drill the 1-1/4" hole for that as well. See examples in the photo."
http://www.thompson-automotive.com/c...11/2029659.htm
#2
Newbie
iTrader: (9)
Join Date: Feb 2002
Location: MI
Posts: 1,171
Likes: 0
Received 0 Likes
on
0 Posts
https://www.rx7club.com/showthread.php?t=391907
.
or you can easily make your own, I made one out of some display board purchased at office max, cost was minimal but it wasn't as nice as a proffessionally made one:
The other smaller hole was for my nitrous switch, must not have had it in at this point.
.
or you can easily make your own, I made one out of some display board purchased at office max, cost was minimal but it wasn't as nice as a proffessionally made one:
The other smaller hole was for my nitrous switch, must not have had it in at this point.
#4
RX-7's since 1980
iTrader: (4)
yes it fits
https://www.rx7club.com/3rd-generation-specific-1993-2002-16/din-panel-gauges-577232/
(snap drive may not work but I did use the thompson panel with three holes.)
https://www.rx7club.com/3rd-generation-specific-1993-2002-16/din-panel-gauges-577232/
(snap drive may not work but I did use the thompson panel with three holes.)
#5
RX-7 Bad Ass
iTrader: (55)
My only beef is having gauges THAT low where it's hard to monitor them while driving. But, I do dig a quality well-made part!
Dale
Dale
#6
Grand Poobah of Torque
Join Date: Jun 2006
Location: Clermont, Florida
Posts: 186
Likes: 0
Received 0 Likes
on
0 Posts
I had one of these before it was stolen and I loved it.
http://hometown.aol.com/flyrx7/Rx7-Gauge-Pod.html
Just be careful if you live in extremely hot climates as the plastic *can* deform. I live in FL and never really had an issue until I parked the car for awhile and the interior temps got very high and started to reshape it slightly.
_Kris
http://hometown.aol.com/flyrx7/Rx7-Gauge-Pod.html
Just be careful if you live in extremely hot climates as the plastic *can* deform. I live in FL and never really had an issue until I parked the car for awhile and the interior temps got very high and started to reshape it slightly.
_Kris
#7
Newbie
iTrader: (9)
Join Date: Feb 2002
Location: MI
Posts: 1,171
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by jacobcartmill
is than an **** probe
if so, why are you injecting nitrous into your anus
if so, why are you injecting nitrous into your anus
Trending Topics
#9
one part from Nirvana
iTrader: (3)
Join Date: Dec 2004
Location: in a van by the river
Posts: 380
Likes: 0
Received 0 Likes
on
0 Posts
[QUOTE=jacobcartmill]i wonder of this will work with our FD's...
If you want a 3 hole panel, we will drill it for you. If you want to be able to install a BRB (Big Red start button from a Honda S-2000) we can drill the 1-1/4" hole for that as well. See examples in the photo."
I used this exact (3 hole) in my Fd, Mechanical water, boost and wideband fit
perfectly, no dremel (went that route the 1st time), well worth the $! I have no problem reading any of the gauges, looks stock and not "ricey" like the pillar mounts.
If you want a 3 hole panel, we will drill it for you. If you want to be able to install a BRB (Big Red start button from a Honda S-2000) we can drill the 1-1/4" hole for that as well. See examples in the photo."
I used this exact (3 hole) in my Fd, Mechanical water, boost and wideband fit
perfectly, no dremel (went that route the 1st time), well worth the $! I have no problem reading any of the gauges, looks stock and not "ricey" like the pillar mounts.