Plugged climate control into blower box. now hazards are on and won't turn off.
#1
Penis Healthy
Thread Starter
iTrader: (5)
Join Date: Jul 2013
Location: █▬█ █▄█ █▬█ █▄██▬█ █▄█ █▬█ █▄█
Posts: 2,595
Received 778 Likes
on
445 Posts
Plugged climate control into blower box. now hazards are on and won't turn off.
Plugged climate control into blower box. now hazards are on and won't turn off.
I'm talking about the plug behind the glovebox.
Even with the climate control unplugged from the harness behind the radio,and still plugged into the blower box, still hazards are on and won't turn off.
Any ideas?
I'm talking about the plug behind the glovebox.
Even with the climate control unplugged from the harness behind the radio,and still plugged into the blower box, still hazards are on and won't turn off.
Any ideas?
#4
Moderator
iTrader: (1)
When the hazard button is depressed it places a ground on the Light Green wire which activates the hazards. The Light Green wire also runs to the alarm, so good call made by you. It really doesn't make sense at first glance why plugging in the blower causes your alarm unit to spaz out. What you could do is return things to as close to normal as they were and then take a voltage reading from some of the alarm control pins/wires and then plug in the item causing the snafu and then retake the voltage measurements from the alarm unit.
Trending Topics
#8
roTAR needz fundZ
iTrader: (1)
Plugged climate control into blower box. now hazards are on and won't turn off.
I did this same thing, you have it plugged into the wrong plug, the long set of wires off the back of the logicon go to a plug under the windshield vents
When you plug it into the plug by the glove box, the hazards kick in, i asked the exact same question about a year ago
When you plug it into the plug by the glove box, the hazards kick in, i asked the exact same question about a year ago
#9
Retired Moderator, RIP
iTrader: (142)
Join Date: Sep 2005
Location: Smiths Falls.(near Ottawa!.Mapquest IT!)
Posts: 25,581
Likes: 0
Received 131 Likes
on
114 Posts
Iduley is right..the Logicon has a connector on the firewall,under the Driver's long dash vents.
If you pop the flat metal piece of the dash, you can "just see" the connector.
It is to the Driver's side of the middle of the firewall.(see the bolt hole for the small 5/32 bolt that held the metal on?..right there!!!).
Mazda really gives you a chore to plug this thing in ..or unplug it.
Snake a piece of string through the dash and you can use it to grab the connector of the logicon and bring it up through to plug it in.
#12
Penis Healthy
Thread Starter
iTrader: (5)
Join Date: Jul 2013
Location: █▬█ █▄█ █▬█ █▄██▬█ █▄█ █▬█ █▄█
Posts: 2,595
Received 778 Likes
on
445 Posts
Found the plug and plugged in the logicon. After replacing the "cool air" fuse, the blower and door worked like a charm. Thanks for all the help. The main purpose of this was to fix my defrosters/defoggers before fall/winter.
Now if I can only find where those heater core hoses ran off too...
Now if I can only find where those heater core hoses ran off too...
Thread
Thread Starter
Forum
Replies
Last Post
trickster
2nd Generation Specific (1986-1992)
25
07-01-23 04:40 PM
The Shaolin
2nd Generation Specific (1986-1992)
9
09-14-15 07:50 PM